manualshive.com logo in svg

HIOS Neji Taro II HS-35, Руководство по эксплуатации

Поделиться
Скачать
HIOS Neji Taro II HS-35 Скачать руководство пользователя страница 3

- 2 -

3. Parts of Names

Note:

①

The design of bit-guide has been changed form V-type to bowl-type since September,1998.

However, the operation method is same as the former V-type , therefore, the descriptions and the drawings for the V-
type are still used in this manual. Pleas be careful that the bit type have been changed.(See p.10)

②

A drop preventive plate is provided in this machine. However, this part should not be touched or maintained by users, 
consequently, the explanations and the drawings for this part are omitted in this manual.

 

Screw bin lid

Power switch

Timing shaft 

Rail screw 

Stopper

Rail

Rail assembly

Sensor

Sensor

Brush

Timer setting control  

Tilt lock screw

Bin dipper plate

Screw passage plate

Shutter (in front of screw pas-

sage plate)

Screw bin

DC jack

Bin scooper plate

Bit guide

Holding plate

(screw guide 1)

Bit guide unit assembly

Screw bin

Bowl type

Passage window (passage 

plate screw passage window)

Passage plate 

lock screw

Содержание Neji Taro II HS-35





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды