![background image](http://html.mh-extra.com/html/hilti/dd-150-u/dd-150-u_manual_2135214013.webp)
*2204402*
2204402
English
5
Power tool use and care
▶
Do not force the power tool. Use the correct power tool for your application.
The correct power tool
will do the job better and safer at the rate for which it was designed.
▶
Do not use the power tool if the switch does not turn it on and off.
Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
▶
Disconnect the plug from the power source and/or remove the battery pack, if detachable, from
the power tool before making any adjustments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting the power tool accidentally.
▶
Store idle power tools out of the reach of children and do not allow persons unfamiliar with the
power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands
of untrained users.
▶
Maintain power tools and accessories. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s operation. If damaged,
have the power tool repaired before use.
Many accidents are caused by poorly maintained power
tools.
▶
Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
▶
Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking
into account the working conditions and the work to be performed.
Use of the power tool for
operations different from those intended could result in a hazardous situation.
▶
Keep handles and grasping surfaces dry, clean and free from oil and grease.
Slippery handles and
grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
Service
▶
Have your power tool serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
2.2
Drill safety warnings
Safety instructions for all operations
▶
Use the auxiliary handle(s).
Loss of control can cause personal injury.
▶
Brace the tool properly before use.
This tool produces a high output torque and without properly
bracing the tool during operation, loss of control may occur resulting in personal injury.
▶
Hold the power tool by insulated gripping surfaces, when performing an operation where the
cutting accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a "live"
wire may make exposed metal parts of the power tool "live" and could give the operator an electric
shock.
Safety instructions for all operations
▶
Use the auxiliary handle(s).
Loss of control can cause personal injury.
▶
Hold the power tool by insulated gripping surfaces, when performing an operation where the
cutting accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a "live"
wire may make exposed metal parts of the power tool "live" and could give the operator an electric
shock.
Safety instructions when using long drill bits
▶
Never operate at higher speed than the maximum speed rating of the drill bit.
At higher speeds,
the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal
injury.
▶
Always start drilling at low speed and with the bit tip in contact with the workpiece.
At higher
speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in
personal injury.
▶
Apply pressure only in direct line with the bit and do not apply excessive pressure.
Bits can bend
causing breakage or loss of control, resulting in personal injury.
2.3
Diamond drill safety warnings
▶
When performing drilling that requires the use of water, route the water away from the operator’s
work area or use a liquid collection device.
Such precautionary measures keep the operator’s work
area dry and reduce the risk of electrical shock.
▶
Operate power tool by insulated grasping surfaces, when performing an operation where the
cutting accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a “live”
Содержание DD 150?U
