Hillyard TRIDENT R30SC, Руководство по эксплуатации и обслуживанию

Страница: 19 / 28

20. RECOMMENDED MAINTENANCE OPERATIONS
Note:
(1) In any event check the battery charge level when working.
1. EMPTYING THE RECOVERY TANK
Proceed as follows to empty the recovery tank:
1. Take the machine to the maintenance area.
2. Make sure the machine has been secured (see the section titled “ SECURING THE MACHINE ”).
CAUTION : users are advised to always wear protective gloves, to avoid the risk of serious injury
to hands.
3. Detach the recovery tank drainage tube (on the back of the machine) from the retainers holding it
in place ( Fig.1 ).
4. Bend the end of the drainage tube in order to create a choke and prevent the content from coming
out ( Fig.2 ), then position the tube on the discharge surface, unscrew the cap, and gradually release
the tube.
NOTE : the place designated for this operation must comply with current environmental
protection regulations.
5. Repeat the operations in reverse order to reassemble all the parts.
2. CLEANING THE SQUEEGEE BODY
The careful cleaning of the whole vacuum unit ensures better drying and cleaning of the floor as well
as a longer vacuum motor life. To carry out the cleaning of the squeegee body, proceed as follows:
1. Take the machine to the maintenance area.
2. Make sure the machine has been secured (see the section titled “ SECURING THE MACHINE ”).
CAUTION : these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
3. Extract the vacuum hose (1) from the vacuum nozzle on the squeegee body (
Fig.1
).
4. Completely unscrew the knobs (2) in the squeegee body's pre-assembly ( Fig.2 ).
5. Remove the squeegee body from the slits in the squeegee connector ( Fig.3 ).
6. Thoroughly clean the squeegee body vacuum chamber (4) with a jet of water, and then with a damp
cloth ( Fig.4 ).
NOTE : the place designated for this operation must comply with current environmental
protection regulations.
7. Thoroughly clean the squeegee body's rear rubber blade (5) with a jet of water, and then with a
damp cloth ( Fig.5 ).
8. Thoroughly clean the squeegee body front rubber blade (6) with a jet of water, and then with a
damp cloth ( Fig.6 ).
9. Thoroughly clean the vacuum nozzle with a jet of water, and then with a damp cloth.
10. Proceed in the opposite order to reassemble all the parts.
3. CLEANING THE BRUSH HEAD BRUSHES (SCRUBBING VERSION)
Careful cleaning of the brush guarantees better cleaning of the floor as well as a longer brush head
gearmotor lifespan. To clean the brush, proceed as follows:
1. Take the machine to the maintenance area.
2. Make sure the machine has been secured (see the section titled “ SECURING THE MACHINE ”).
CAUTION : these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
3. Open the machine's left lateral carter (1) ( Fig.1 ).
4. Remove the side splash guard support (2) by loosening the knobs (3) on it ( Fig.2 ).
5. Press the brush locking pin (4) ( Fig.3 ).
6. Keeping the pin (4) pressed, turn the brush clockwise until it is locked ( Fig.4 ).
7. Turn until the button is pushed towards the outside of the coupling spring and is locked into place.
4. CLEANING THE RECOVERY TANK FILTERS
In order to clean the filters present inside the recovery tank, do the following:
1. Take the machine to the maintenance area.
2. Make sure the machine has been secured (see the section titled “ SECURING THE MACHINE ”).
CAUTION : users are advised to always wear protective gloves, to avoid the risk of serious injury
to hands.
NOTE : the place designated for this operation must comply with current environmental
protection regulations.
3. Grip the handle (1) and raise the recovery tank's lid to its maintenance position ( Fig.1 ).
4. Remove the dirty water basket/filter from the support (2) ( Fig.2 ).
5. Remove the basket cover (3) from the basket/filter (2) ( Fig.3 ).
6. Clean the basket/filter (2) and the basket cover (3) under a jet of water.
NOTE
: Use a spatula or brush to eliminate any dirt that is particularly difficult to remove.
7. Use a dry cloth to dry the basket/filter (2) and the basket cover (3) and place them back inside the
recovery tank.
8. Remove the vacuum motor filter from the support (4) ( Fig.4 ).
9. Extract the dirt present inside the vacuum motor's filter (4).
8. Clean the brush under a stream of running water to remove any impurities from its bristles. Check
the wear status of the bristles and replace the brushes if they are excessively consumed (the bristles'
protrusion must not be less than 10 mm; this distance is indicated on the brush by the yellow band).
Read the paragraph “ BRUSH HEAD BRUSHES REPLACEMENT (SCRUBBING VERSION) ”.
9. After checking to make sure that the brush is clean, reassemble it and move on to the one on the
right hand side.
NOTE : you are advised to invert the right and left-hand brushes every day.
NOTE : Image 3 indicates the direction of rotation for coupling the left brush; the right brush must
be turned in the opposite direction.
ATTENTION : If the brushes are not new however, and have deformed bristles, it is better to
reassemble them in the same position (the right-hand one on the right, and the left-hand one
on the left), to prevent the different inclination of the bristles producing an overload on the
brush motor as well as excessive vibrations.
19
2 1
2 3 1
1 2
6 4 5
3
4
2 3 1
1
2
3
4
4
2 3 1
1
2
3
TYPE OF MAINTENANCE
AT THE END OF THE WORK DAIL
Y
WEEKL
Y
BEFORE A
LONG
PERIOD OF NON- USE TRANSPORT
EMPTYING THE RECOVERY TANK X X X
CLEANING THE SQUEEGEE BODY X X X
CLEANING THE BRUSH HEAD BRUSHES
(SCRUBBING VERSION)
X X
CLEANING THE RECOVERY TANK FILTERS X X
CLEANING THE RECOVERY TANK X X
EMPTYING THE SOLUTION TANK X X X
(1)
RECHARGING THE BATTERIES X
CLEANING THE WATER SYSTEM FILTER X X
CLEANING THE VACUUM TUBE X X