Hillyard TRIDENT R30SC, Руководство по эксплуатации и обслуживанию

Страница: 13 / 28

16. MACHINE PREPARATION
1. HANDLING THE PACKAGED MACHINE
The machine's overall weight including packaging is 685lb.
NOTE : it is recommended that all the packaging components be kept for any future machine
transportation.
DANGER : Move the packaged product with handling equipment that complies with legal
requirements regarding size and mass of the packaging.
2. HOW TO UNPACK THE MACHINE
The machine is shipped in specific packaging. To remove it, proceed as follows:
1. Place the lower part of the outer packaging in contact with the floor.
NOTE : use the pictograms printed on the box as a reference.
2. Remove the outer package.
WARNING : the machine is contained in specific packaging materials, whose elements (plastic
bags, staples, etc.) can pose potential hazards, and must not be left within reach of children,
disabled persons, etc.
3. Remove the boxes containing the disc brushes and squeegee body from the machine.
CAUTION
: these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
4. Insert a ramp in the rear part of the machine.
ATTENTION : the ramp gradient must not be such as to cause damage to the machine as it
comes down.
5. The machine is fixed to the pallet with wedges (1) that block the wheels ( Fig.1 ). Remove these
wedges.
6. Check to make sure that the main switch on the control panel has been set to its “0” position. If
this is not the case, turn the key (2) a quarter turn to the left ( Fig.2 ). Remove the key from the
main switch.
7. Grip the handle (3) and raise the recovery tank to the maintenance position ( Fig.3 ).
8. Connect the backup battery carriage's connector to the machine's main system connector
( Fig.4 ).
9. Grip the handle (3) and lower the recovery tank to its working position ( Fig.5 ).
10. Sit on the driver’s seat.
11. Insert the key (1) into the main switch on the control panel. Set the main machine switch to its "I"
position, by turning the key a quarter turn to the right ( Fig.6 ).
12. Turn the brush head control level (4) anti-clockwise ( Fig.7 ); in this manner the brush head body
will be raised off the pallet.
13. Turn the squeegee control lever (5) clockwise ( Fig.8 ) to raise the squeegee body off the pallet.
14. Engage the reverse gear using the reverse gear activation/deactivation lever (6) ( Fig.9 ).
3. HOW TO MOVE THE MACHINE
To transport the machine safely, proceed as follows:
DANGER : before starting any task, make sure the current regulations concerning the safe
transport of dangerous substances are scrupulously observed.
1. Check to make sure that the solution tank and the recovery tank are empty. If this is not the case,
empty them (see the sections titled “ EMPTYING THE SOLUTION TANK ” and “ EMPTYING THE
RECOVERY TANK ”).
2. Sit on the driver’s seat.
3. Insert the key (1) into the main switch on the control panel. Bring the main switch to its "I" position
by turning the key (1) a quarter turn to the right ( Fig.1 ).
4. Turn the brush head control lever (2) anti-clockwise ( Fig.2 ); in this manner the brush head body
will be raised off the floor.
5. Turn the squeegee control lever (3) clockwise ( Fig.3 ) to raise the squeegee body off the floor.
6. Press the drive pedal (4) ( Fig.4 ) to begin moving the machine.
7. Use a ramp to move the machine up onto the transport vehicle.
CAUTION : during this operation, check there are no people or objects near the machine.
NOTE : the ramp gradient must not be such as to cause damage to the machine as it goes up.
8. Position the machine on the means of transport, and set the main switch to its “0” position by
turning the key (1) a quarter turn anti-clockwise (
Fig.5
). Remove the key from the main switch.
9. Get off the machine.
10. Grip the handle (5) and raise the recovery tank to its maintenance position ( Fig.6 ).
15. Press the drive pedal (7) ( Fig.10 ) to begin moving the machine.
16. Drive the machine down the ramp.
ATTENTION: during this operation, check there are no people or objects near the machine.
17. Bring the main switch to its "0" position by turning the key (1) a quarter turn anti-clockwise
( Fig.2 ). Remove the key from the main switch.
18. Get off the machine.
19. Grip the handle (2) and raise the recovery tank to its maintenance position ( Fig.3 ).
20. Disconnect the backup battery carriage's connector from the machine's main system connector
( Fig.4 ).
21. Grip the handle (4) and lower the recovery tank to its working position ( Fig.5 ).
11. Disconnect the battery connector from the machine's main system connector ( Fig.7 ).
12. Grip the handle (5) and lower the recovery tank to its working position ( Fig.8 ).
WARNING : secure the device according to the directives in force in the country of use, so that
it cannot slide or tip over.
13
3
4
1
1
3
2
2
6
1
5
3
0
0
ON
ON
7 8
4
5
9
6
10
7
3 2
2
3
4
4
6
5
7 8
5
2
2
2
1
A 55,91in
B 40,31in
C 69,29in