HIKVISION DS-K3B801SX Series страница 47 Скачать руководство пользователя | Manualshive

Страница: 47 / 72

background image

Use the jumper cap to switch the serial port communication mode with the lane controller. By

default, the interface is wired and it is in RS-485 communication mode. If wiring other

controllers (compatible with Hikvision communication protocol), use the jumper cap to switch

between RS-485 and RS-232 communication mode.

UART4

The serial port is in the wiring interface according to the picture above, which has a fixed RS-232

communication mode to communicate with the main lane controller. It contains no jumper cap

and cannot change the communication mode.

UART7/UART8

Reserved serial port. The serial port has a fixed RS-232 communication mode. It contains no

jumper cap and cannot change the communication mode, which can connect with a QR code

scanner.

The reserved interface positions in the turnstile and their corresponded UART No. are as follows:

Note

The diagram is for reference only.

Figure 5-11 Interface and Corresponded UART No.

DS-K3B801SX Series Swing Barrier Quick Start Guide

36

«
...
45
46
47
48
49
...
»

Содержание DS-K3B801SX Series









































































Отзывы:

Нет отзывов

Похожие инструкции для DS-K3B801SX Series

Бренд: ZKTeco Страницы: 7

ProEntrance Series

Бренд: ZKTeco Страницы: 8

Бренд: Thorn Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды