manualshive.com logo in svg

HIKVISION DS-K3B801SX Series, Быстрый старт

Поделиться
Скачать
HIKVISION DS-K3B801SX Series Скачать руководство пользователя страница 55

Note

• Only one turnstile can pair the keyfob. If multiple turnstiles are in the pairing mode, the

keyfob will select only one of them to pair.

• For details about DIP switch value and meaning, see DIP Switch .

6. Optional: Go to System → User → Keyfob User on the remote control page of the client

software to delete the keyfob.

6.3 Initialize Device

Steps

1. Remove the JP11 jumper cap on the access control board.

Figure 6-1 Initialization Jumper Cap

2. Disconnect the power and reboot the device. The device buzzer buzzes a long beep.

3. When the beep stopped, plug the jumper cap back.

4. Disconnect the power and power on the device again.

Caution

The initialization of the device will restore all the parameters to the default setting and all the

device events are deleted.

Note

Make sure no persons are in the lane when powering on the device.

DS-K3B801SX Series Swing Barrier Quick Start Guide

44

Содержание DS-K3B801SX Series









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды