HIKVISION DS-K3B801SX Series Скачать руководство пользователя

Страница: 45 / 72

Access Control Board Terminal Description

D2+

Alarm Output

NO/NC1

Alarm Output Relay 1 (Dry Contact)

COM1
NO/NC2

Alarm Output Relay 2 (Dry Contact)

COM2
NO/NC3

Alarm Output Relay 3 (Dry Contact)

COM3
NO/NC4

Alarm Output Relay 4 (Dry Contact)

COM4

Network Interface

LAN

Network Accessing

Note

• The alarm input hardware interface is normally open by default. So only the normally open

signal is allowed. It can be linked to the buzzer of the card reader and access controller, and the

alarm relay output and open door relay output.

• The DIP of RS-485 card ID is set as 1 and 4 by default. 1 is for entering, and 4 is for exiting. If the

user has configured visitor card, you should connect two card readers on the exiting side. Set the

DIP switch of one of the card reader as 4, and set the other one's as 3.

Card Reader 3 should be used together with the card recycler.

Normal users should present card on Card Reader 4, while visitors should present card on Card

Reader 3.

• The Wiegand card reader 1 and 2 refer to the entering and exiting card reader respectively.

• The alarm output supports relay output.

• For any requirements, the door lock can control the door barrier status of the third party. D1

controls the barrier opening for entrance, while D2 controls the door opening for exit. For

details, see Barrier Control Relay Output Mode .

• C3 and C4 in the event input can also be people counting interface. C3 controls people counting

for entrance, while C4 controls people counting for exit. When the access control board detects

signals in C3 and C4, the people number will be accumulated. For detailed information about

people counting and people number, see Configuring People Counting Parameters in User

Manual of iVMS-4200 AC Client Software.

• For detailed information about the DIP switch, see DIP Switch .

DS-K3B801SX Series Swing Barrier Quick Start Guide

Содержание DS-K3B801SX Series









































































Результаты поиска

Содержание DS-K3B801SX Series

Отзывы:

Похожие инструкции для DS-K3B801SX Series

Бренды по названию

Популярные бренды

HIKVISION DS-K3B801SX Series, Быстрый старт

Результаты поиска

Содержание DS-K3B801SX Series

Отзывы:

Похожие инструкции для DS-K3B801SX Series

Бренды по названию

Популярные бренды