HIKVISION DS-K3B801SX Series Скачать руководство пользователя

Страница: 4 / 72

Regulatory Information

FCC Information

Please take attention that changes or modification not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

FCC compliance: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

—Consult the dealer or an experienced radio/TV technician for help

This equipment should be installed and operated with a minimum distance 20cm between the

radiator and your body.

FCC Conditions

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause

undesired operation.

EU Conformity Statement

This product and - if applicable - the supplied accessories too are marked with "CE"

and comply therefore with the applicable harmonized European standards listed

DS-K3B801SX Series Swing Barrier Quick Start Guide

iii

Содержание DS-K3B801SX Series









































































Результаты поиска

Содержание DS-K3B801SX Series

Отзывы:

Похожие инструкции для DS-K3B801SX Series

Бренды по названию

Популярные бренды

HIKVISION DS-K3B801SX Series, Быстрый старт

Результаты поиска

Содержание DS-K3B801SX Series

Отзывы:

Похожие инструкции для DS-K3B801SX Series

Бренды по названию

Популярные бренды