HIKVISION 114-029 Скачать руководство пользователя страница 95

Страница: 95 / 190

Network Camera User Manual

can live view them, but cannot record or playback them.

Notes:

•

Custom video function requires the support of the camera.

•

After a camera restore action (not restore to default setting), quantity of custom

video streams and their names are kept, but the related parameters are restored.

Custom Video Settings

Steps:

Click

to add a stream

Change the stream name if needed.

Note:

Up to 32 letters and symbols (except &, <, >, ', or ") are allowed for the

stream name.

Customize the stream parameters (resolution, frame rete, max. bitrate, video

encoding). For parameter introduction, see

Section 8.1.1

(Optional) Add stream description is needed.

(Optional) If a custom stream is not needed, click

to delete it.

Save the settings.

Содержание 114-029































































































































































































Результаты поиска

Содержание 114-029

Отзывы:

HIKVISION 114-029, Руководство пользователя, Страница: 95 / 190

Результаты поиска

Содержание 114-029

Отзывы: