HIKVISION 114-029 Скачать руководство пользователя страница 53

Страница: 53 / 190

Network Camera User Manual

exporting.

Note:

You need to reboot the camera after importing configuration file.



Upgrade

: Upgrade the device to a certain version.

Steps:

Select firmware or firmware directory to locate the upgrade file.

Firmware: Locate the exact path of the upgrade file.

Firmware Directory: Only the directory the upgrade file belongs to is

required.

Click

Browse

to select the local upgrade file and then click

Upgrade

to start

remote upgrade.

Note:

The upgrading process will take 1 to 10 minutes. Please don't disconnect

power of the camera during the process, and the camera reboots automatically

after upgrade.

Log

Purpose:

The operation, alarm, exception and information of the camera can be stored in log

files. You can also export the log files on your demand.

Before you start:

Please configure network storage for the camera or insert a SD card in the camera.

Steps:

Enter log searching interface:

Configuration

System

Maintenance

Log

Log Searching Interface

Содержание 114-029































































































































































































Результаты поиска

Содержание 114-029

Отзывы:

HIKVISION 114-029, Руководство пользователя, Страница: 53 / 190

Результаты поиска

Содержание 114-029

Отзывы: