HIKVISION 114-029 Скачать руководство пользователя страница 169

Страница: 169 / 190

Network Camera User Manual

168

Quota Settings

Note:

Up to 8 NAS disks can be connected to the camera.

Memory Card Detection

Purpose:

With memory card detection, you can view the memory card status, lock your

memory card, and receive notification when your memory card is detected abnormal.

Note:

Memory card detection function is only supported by certain types of memory

cards and camera models. If this tab page doesn't show on your web page, it means

either that your camera doesn't support the function, or your installed memory card is

not supported for this function. You can contact the dealer or the retailer for the

information of memory card that supports the function.

Steps:

Enter Memory Card Detection configuration interface:

Configuration > Storage > Storage Management > Memory Card Detection

Содержание 114-029































































































































































































Результаты поиска

Содержание 114-029

Отзывы:

HIKVISION 114-029, Руководство пользователя, Страница: 169 / 190

Результаты поиска

Содержание 114-029

Отзывы: