HIKVISION 114-029 Скачать руководство пользователя страница 66

Страница: 66 / 190

Network Camera User Manual

TCP/IP Settings

Configure the basic network settings, including the NIC Type, IPv4 or IPv6

Address, IPv4 or IPv6 Subnet Mask, IPv4 or IPv6 Default Gateway, MTU settings

and Multicast Address.

(Optional) Check the checkbox of

Enable Multicast Discovery

, and then the

online network camera can be automatically detected by client software via

private multicast protocol in the LAN.

Configure the DNS server. Input the preferred DNS server, and alternate DNS

server.

Click

Save

to save the above settings

Notes:



The valid value range of MTU is 1280 to 1500.



The Multicast sends a stream to the multicast group address and allows multiple

clients to acquire the stream at the same time by requesting a copy from the

Содержание 114-029































































































































































































Результаты поиска

Содержание 114-029

Отзывы:

HIKVISION 114-029, Руководство пользователя, Страница: 66 / 190

Результаты поиска

Содержание 114-029

Отзывы: