HIKVISION 114-029 Скачать руководство пользователя страница 16

Страница: 16 / 190

Network Camera User Manual

failed, please make sure that the password meets the requirement and try again.

Change the device IP address to the same subnet with your computer by either

modifying the IP address manually or checking the checkbox of Enable DHCP.

Modify the IP Address

Input the admin password and click

Modify

to activate your IP address

modification.

The batch IP address modification is supported by the SADP. Refer to the user manual

of SADP for details.



Activation via Client Software

The client software is versatile video management software for multiple kinds of

devices.

Get the client software from the supplied disk or the official website, and install the

software according to the prompts. Follow the steps to activate the camera

Steps:

Run the client software and the control panel of the software pops up, as shown in

Содержание 114-029































































































































































































Результаты поиска

Содержание 114-029

Отзывы:

HIKVISION 114-029, Руководство пользователя, Страница: 16 / 190

Результаты поиска

Содержание 114-029

Отзывы: