HIKVISION 114-029 Скачать руководство пользователя страница 47

Страница: 47 / 190

Network Camera User Manual

Note:

If the camera is connected to a public network, you should use a NTP server

that has a time synchronization function, such as the server at the National Time

Center (IP Address: 210.72.145.44). If the camera is set in a customized network,

NTP software can be used to establish a NTP server for time synchronization.



Configure the manual time synchronization.

(1)

Check the

Manual Time Sync.

item to enable the manual time

synchronization function.

(2)

Click the icon

to select the date, time from the pop-up calendar.

(3)

(Optional) You can check

Sync. with computer time

item to synchronize the

time of the device with that of the local PC.

Time Sync Manually



Click

Save

to save the settings.

Configuring RS232 Settings

The RS232 port can be used in two ways:



Consolo: Connect a computer to the camera through the serial port. Device

parameters can be configured by using software such as HyperTerminal. The

serial port parameters must be the same as the serial port parameters of the

camera.



Transparent Channel: Connect a serial device directly to the camera. The serial

device will be controlled remotely by the computer through the network.

Steps:

Содержание 114-029































































































































































































Результаты поиска

Содержание 114-029

Отзывы:

HIKVISION 114-029, Руководство пользователя, Страница: 47 / 190

Результаты поиска

Содержание 114-029

Отзывы: