15
English
Always ON (turn o
ff
after 2 minute)
Light only SW
-
ON
Always OFF
Remaining battery indicator switch
Battery
Lights ;
The battery remaining power is over 75%
Lights ;
The battery remaining power is 50% – 75%.
Lights ;
The battery remaining power is 25% – 50%.
Lights ;
The battery remaining power is less than 25%
Blinks ;
The battery remaining power is nearly empty.
Recharge the battery soonest possible.
Blinks ;
Output suspended due to high temperature.
Remove the battery from the tool and allow it to
fully cool down.
Blinks ;
Output suspended due to failure or malfunction.
The problem may be the battery so please
contact your dealer.
NOTE
To prevent the battery power consumption caused by
forgetting to turn o
ff
the LED light, the light goes o
ff
automatically in about 2 minutes.
STANDARD ACCESSORIES
In addition to the main unit (1 unit), the package contains the
accessories listed on page 93.
Standard accessories are subject to change without notice.
APPLICATIONS
Cutting various types of wood.
SPECIFICATIONS
1. Power tool
Model
C3605DA
Voltage
36 V
No
-
Load Speed
5000 /min (Power mode)
2600 /min (Silent mode)
Capacity Cutting
depth
90°
47 mm
45°
30 mm
Battery available for this tool*
Multi volt battery
Weight
2.7 kg (BSL36A18)
3.0 kg (BSL36B18)
* Existing batteries (BSL3660/3620/3626, BSL18xx series,
etc.) cannot be used with this tool.
NOTE
Due to HiKOKI’s continuing program of research and
development, the speci
fi
cations herein are subject to
change without prior notice.
Electronic control
○
Soft
-
start
○
Overload protection
This protection feature cuts o
ff
the power to the motor
in the event of overloading of motor or a conspicuous
reduction in rotational speed during operation.
When the overload protection feature has been
activated, the motor may stop.
In this case, release the tool switch and eliminate causes
of overloading.
After that you can use it again.
○
Overheat protection
This protection feature cuts o
ff
the power to the motor
and stops the power tool in the event of overheating of
motor during operation.
When the overheat protection feature has been
activated, the motor may stop.
In this case, release the tool switch and cool it down in a
few minutes.
After that you can use it again.
○
Rotation speed changeover function (Power mode /
Silent mode)
(Power mode / Silent mode switch function)
Each press of the Mode Selector Switch changes the
operating mode. (
Fig. 16
)
Silent mode reduces maximum motor RPM enabling
e
ffi
cient work with less noise.
The Silent Mode Indicator Lamp lights in Silent mode.
When the load increases during Silent mode, the tool will
automatically switch to Power mode and revert back to
Silent mode when the load decreases.
In Power mode, no change is made to Silent mode even
when the load decreases.
NOTE
○
To enable mode changes, pull the switch once after
installing the battery.
○
Do not give a strong shock to the switch panel or break it.
It may lead to a trouble.
2. Battery
Model
BSL36A18
Voltage
36 V / 18 V (Automatic Switching*)
Battery capacity
2.5 Ah / 5.0 Ah
(Automatic Switching*)
Available cordless
products**
Multi volt series, 18 V product
Available charger Sliding charger for lithium ion batteries
* The tool itself will automatically switch over.
** Please see our general catalogue for details.
CHARGING
Before using the power tool, charge the battery as follows.
1. Connect the charger
’
s power cord to the receptacle.
When connecting the plug of the charger to a receptacle,
the charge indicator lamp will blink in red (At 1
-
second
intervals).
2. Insert the battery into the charger.
Firmly insert the battery into the charger as shown in
Fig. 24
(on page 6).
00Book̲C3605DA̲Asia.indb 15
00Book̲C3605DA̲Asia.indb 15
2018/12/21 14:39:15
2018/12/21 14:39:15
