High End Systems Studio Command 1200 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 108

background image

CHAPTER 2

Setup and Configuration

14

Studio Command Series User Manual

Cable Connectors:

Studio Command 1200/700 fixtures can accept either 3-pin or 5-pin XLR cable connectors.
Studio Command H fixtures use 3-pin XLR cable connectors only. Cabling must have a male XLR
connector on one end of the cable and a female XLR connector on the other end. The following
diagram shows the pin configuration for both cable types.

Test each cable with a voltage/ohm meter (VOM) to verify correct polarity and to make sure that
the negative and positive pins are not grounded or shorted to the shield or to each other.

Caution: Do not connect anything to the ground lug on the XLR

connectors. Do not connect or allow contact between the
common (cable shield) and the fixture’s chassis ground.
Grounding the common could cause a ground loop and/or
erratic behavior.

positive
(data true)

negative
(data
complement)

Common
(cable shield)

positive
(data true)

negative
(data
complement)

XLR shell

Common
(cable shield)

Grounding lug (inside XLR shell)

Male XLR Connector

Female XLR Connector

positive
(data true)*

negative
(data
complement)*

Common
(cable shield)

2

1

3

positive
(data true)

negative
(data
complement)

XLR shell

Common
(cable shield)

1

2

3

4

5

5

4

positive
(data true)*

negative
(data complement)*

negative
(data
complement)

positive
(data true)

*This data line is not used by the fixture, but allows data to pass through the fixture.

Grounding lug (inside XLR shell)

Male 3-pin XLR Connector

Female 3-pin XLR Connector

Male 5-pin XLR Connector

Female 5-pin XLR Connector

Pin configuration for 3-pin (Studio Command 1200/700 model only) and 5-pin XLR cables

«
...
22
23
24
25
26
...
»

Содержание Studio Command 1200













































































































Отзывы:

Нет отзывов

Похожие инструкции для Studio Command 1200

Бренд: Gainsborough Страницы: 3

Бренд: Wagan Страницы: 7

Бренд: Fein Страницы: 150

Бренд: B-K lighting Страницы: 2

Бренд: Skytec Страницы: 16

Бренд: jedi LIGHTING Страницы: 27

Бренд: RAB Lighting Страницы: 2

Бренд: Blizzard Lighting Страницы: 16

Бренд: Mark Страницы: 24

SR95S Intimidator

Бренд: OLIGHT Страницы: 2

Бренд: Black & Decker Страницы: 2

LEV112318M840TE

Бренд: Toshiba Страницы: 18

Бренд: raya Страницы: 20

Бренд: StreamLight Страницы: 2

Бренд: Ryobi Страницы: 7

Бренд: Ryobi Страницы: 64

Бренд: Groz Страницы: 4

Бренд: Flexlite Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды