High End Systems intellaspot XT-1 Скачать руководство пользователя страница 74

Страница: 74 / 98

CHAPTER 5

General Maintenance and Troubleshooting

intellaspot

XT-1 User Manual

Replacing Parts

Replacing Fuses

To replace a fuse:

1. Disconnect power to the fixture. If the fixture has been operating, allow the fixture to cool

before handling.

2. Use the following table to determine which fuse to replace and its location

3. Replace the appropriate fuse(s) with a fuse of the same type and rating shown in the following

table.

Note:

(F2) on the Pan and Tilt boards has a spare fuse that can be used for any of
the motor driver boards.

WARNING: Disconnect power before servicing. Replace fuses with the
specified type and rating only.

Equipment surfaces may reach temperatures up to 130° C (266° F). Allow
the fixture to cool before handling.

Fuse

Fuse Location

Symptom of Failure

Module Link

One fuse inside the electronics
housing on top of power supply.

Fixture shuts down and will not receive
power.

2-phase motor driver boards

Two fuses [F1] and [F2] on each
module driver board

below the

connector.

Module motors will be off. Each fuse
protects two of the 4 motors associated with
each board. Board LEDs will remain on.

3-phase Pan and Tilt boards

[F1] on Tilt board in the head near
the fixture lens.

Pan or Tilt board-related motors and fans
will be off.

[F1] on Pan board in the electronic
housing behind the display panel

Display Board

[F1] next to the Module Link header

Display will not operate

Battery

On display board next to battery

Fuse

Fuse Type and Rating

Manufacturer

HES p/n

Module Link

6.3A, 250 V, Slow Blow

Littelfuse 326 015 or
Bussmann MDA-15

90403019EF

Battery

1.5A, 125 V slow blow SMF

Order from High End
Systems

90412029EF

2-phase driver boards

2.5 A, 125 V, Slow Blow SMF

Littelfuse R454 02.5

90402024

3-phase motor driver boards

Display board

Содержание intellaspot XT-1



































































































Результаты поиска

Содержание intellaspot XT-1

Отзывы:

Похожие инструкции для intellaspot XT-1

Бренды по названию

Популярные бренды

High End Systems intellaspot XT-1, Руководство пользователя

Результаты поиска

Содержание intellaspot XT-1

Отзывы:

Похожие инструкции для intellaspot XT-1

Бренды по названию

Популярные бренды