HIAB Hooklift Multilift XR S Series страница 109 Скачать руководство пользователя

Страница: 109 / 160

109

4/2018

113175421

XR14S/16S/18S/21S/26S/30S

Hooklift Multilift XR S

Service Manual

Hooklift supported to tipping position

If the work is done under the rear frame, the equipment must be lifted to tipping position

and the frames supported with separate tipping support in the correct places. Remember

to remove the support after the work has been completed.

BE AWARE!

Never move the middle frame or the rear frame by means

of hydraulics against the tipping support. The equipment

cylinders are powerful enough to break the support or the

frames and there is a great risk of personal injury. Stop the

movement of the main cylinders immediately when the frame

reaches the support.

Stop the truck engine always when doing service work under the raised frame and under

the container.

Use ladders and working platforms when required.

Do not utilise the hooklift components for climbing up the equipment.

Содержание Hooklift Multilift XR S Series

































































































































































Результаты поиска

Содержание Hooklift Multilift XR S Series

Отзывы:

Похожие инструкции для Hooklift Multilift XR S Series

Бренды по названию

Популярные бренды

HIAB Hooklift Multilift XR S Series, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание Hooklift Multilift XR S Series

Отзывы:

Похожие инструкции для Hooklift Multilift XR S Series

Бренды по названию

Популярные бренды