HIAB Hooklift Multilift XR S Series Скачать руководство пользователя страница 33

Страница: 33 / 160

4/2018

Hooklift Multilift XR S

User Manual

113175421

XR14S/16S/18S/21S/26S/30S

16.

Move the hook arm forward

- move the control lever to left and forward.

Continue the movement until the container is in its transport position.

Movement will close also the mechanical tipping lock.

17.

Close the hydraulic body locks

- press the “body locks closed” button

Signal light “locks not closed” must go out.

Also close the mechanical or hydraulic front locks (optional).

18.

If the truck is equipped with any of the following equipment, do the following:

- extend/fold out the adjustable under-run bar (mechanical or manual hydraulic)

- re-inflate the air suspension

- release the bogie blocking cylinders or lift up the stabilising roller.

19.

Press the clutch pedal and disengage the PTO.

20.

Check that all signal lights of the control unit have gone out.

NOTE! If there is a safety code CXXX and/or dXXX in the display,

then see the chapter ”Safety codes” after the chapter ”Loading a container”.

The loading will start in most cases but the reason to the code must be checked

and repaired as soon as possible to avoid any risk to injuries or damages.

Safety codes >

Содержание Hooklift Multilift XR S Series

































































































































































Результаты поиска

Содержание Hooklift Multilift XR S Series

Отзывы:

Бренды по названию

Популярные бренды

HIAB Hooklift Multilift XR S Series, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание Hooklift Multilift XR S Series

Отзывы:

Бренды по названию

Популярные бренды