HIAB Hooklift Multilift XR S Series страница 41 Скачать руководство пользователя

Страница: 41 / 160

4/2018

Hooklift Multilift XR S

User Manual

113175421

XR14S/16S/18S/21S/26S/30S

Decrease the speed of tipping movement to prevent an abrupt stop during the

last tipping phase.

10.

Release the parking brake and drive, if needed, a little forward in order to

empty the complete contents of the container.

- the PTO can be engaged during this phase.

11.

Engage the parking brake.

Lowering the tipping device

12.

Lower the tipping device

- move the control lever forward

13.

Check that the frame of the XR equipment and the container are in the lowest

position.

14.

Close the container tail gate.

Also close the mechanical or hydraulic front locks (optional).

15.

If the truck is equipped with any of the following equipment, do the following:

- extend the adjustable under-run bar (mechanical or manual hydraulic)

- re-inflate the air suspension.

16.

Press the clutch pedal and disengage the PTO.

17.

Check that all signal lights of the control unit have gone out.

NOTE! If there is a safety code CXXX and/or dXXX in the display,

then see the chapter ”Safety codes” after the chapter ”Tipping a container”.

The tipping will start in most cases but the reason to the code must be checked

and repaired as soon as possible to avoid any risk to injuries or damages.

Safety codes >

Содержание Hooklift Multilift XR S Series

































































































































































Результаты поиска

Содержание Hooklift Multilift XR S Series

Отзывы:

Похожие инструкции для Hooklift Multilift XR S Series

Бренды по названию

Популярные бренды

HIAB Hooklift Multilift XR S Series, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание Hooklift Multilift XR S Series

Отзывы:

Похожие инструкции для Hooklift Multilift XR S Series

Бренды по названию

Популярные бренды