Hi-Vac X-Vac Hydro Excavator X15 Series Скачать руководство пользователя страница 38

Страница: 38 / 87

SERVICE 6

AQUATECH OPERATIONS, SERVICE AND PARTS MANUAL

A Product of Hi-Vac Corporation

SERVICE

ELECTRICAL SYSTEM

CONDITION

PROBABLE CAUSES

REMEDIES

NO POWER

Ignition/unit power switch not “on”.

Turn ignition/unit power

switch “on”.

BOOM VALVE NOT WORKING

Faulty solenoid valve.

Check for voltage at

solenoid. Replace.

FUSE BLOWN

(#1 TERMINAL BLOCK,

#2 AMP REPLACEMENT).

1. Frayed or broken harness wire.

2. Short circuit in solenoid(s) wiring

connection.

3. Switch terminal arcing within

housing.

1. Repair or replace.

2. Check for pinched or

bare wire connections.

3. Secure terminal to post

connections on switch.

PTO WON’T RE-ENGAGE DRIVE

AXLE.

Switches turned off in wrong

sequence.

Unit power must be last

switch turned off.

PTO DOES NOT DISENGAGE

DRIVE AXLE.

Faulty solenoid valve

Check for voltage at

solenoid. Replace

PENDANT BOOM SWITCHES

FUNCTION ERRATICALLY.

1. Push button, switch terminals

loose or disconnected.

2. Push button switch contacts

burned or disconnected.

3. Water in pendant

1. Tighten or reconnect. 2.

Replace switch unit.

3. Dry out pendant control

and seal leaks.

FLAPPER VALVE INTAKE

CYLINDER ON BOOM

INOPERATIVE.

1. Pneumatic valve solenoid coil

burned out.

2. Valve spool stuck or unsealed.

3. Wiring from valve to control box

broken or disconnected.

1. Test and replace if neces-

sary.

2. Disassemble, clean, or

replace.

3. Repair and replace.

IMPORTANT!

Do not attempt to remedy any electrical problems without first examining the schematic wiring diagram and control

wiring circuit drawing (see Electrical Section). Check truck chassis battery and cell condition. Use proper

instrumentation for current and continuity test results.

(A) Continuity- Use OHM scale recorder or battery powered continuity test light.

(B) Current- The circuit must be opened to obtain current reading with the volt- meter; therefore, it is more

convenient to use a 12 VDC test light.

TROUBLESHOOTING COMMON PROBLEMS

The following is a list of possible problems which may be encountered during the life of this machine. Probable

causes are listed in this section together with recommended solutions to these problems. If the resolution of these

problems or any other problems are not readily apparent, contact your local authorized X-Vac dealer.

Содержание X-Vac Hydro Excavator X15 Series
























































































Результаты поиска

Содержание X-Vac Hydro Excavator X15 Series

Отзывы:

Похожие инструкции для X-Vac Hydro Excavator X15 Series

Бренды по названию

Популярные бренды

Hi-Vac X-Vac Hydro Excavator X15 Series, Инструкция по эксплуатации, обслуживанию и ремонту

Результаты поиска

Содержание X-Vac Hydro Excavator X15 Series

Отзывы:

Похожие инструкции для X-Vac Hydro Excavator X15 Series

Бренды по названию

Популярные бренды