Hi-Vac X-Vac Hydro Excavator X15 Series Скачать руководство пользователя страница 25

Страница: 25 / 87

PRINCIPLES OF OPERATION 13

AQUATECH OPERATIONS, SERVICE AND PARTS MANUAL

A Product of Hi-Vac Corporation

PRINCIPLES OF OPERATION

DEBRIS PROBE OPTION

The

Debris Probe

is used to set off an alarm and illuminate a warning light when a predetermined

level has been reached in the Debris Tank. When this occurs, the operator can turn off the alarm

by using the toggle switch.

The operator shoud then follow the instructions for

“Dumping The Debris Tank”

, outlined in the

“Principles of Operation”

section of this manual.

Debris

Probe

Note: For information on this option, refer to the vendor literature (if included as

an option) located in the “Controls” section and on the Digital Copy

supplied with this unit.

Содержание X-Vac Hydro Excavator X15 Series
























































































Результаты поиска

Содержание X-Vac Hydro Excavator X15 Series

Отзывы:

Похожие инструкции для X-Vac Hydro Excavator X15 Series

Бренды по названию

Популярные бренды

Hi-Vac X-Vac Hydro Excavator X15 Series, Инструкция по эксплуатации, обслуживанию и ремонту

Результаты поиска

Содержание X-Vac Hydro Excavator X15 Series

Отзывы:

Похожие инструкции для X-Vac Hydro Excavator X15 Series

Бренды по названию

Популярные бренды