Hi-Vac X-Vac Hydro Excavator X15 Series Скачать руководство пользователя страница 37

Страница: 37 / 87

SERVICE 5

AQUATECH OPERATIONS, SERVICE AND PARTS MANUAL

A Product of Hi-Vac Corporation

SERVICE

CONDITION: LOSS OF VACUUM

PROBABLE CAUSES

REMEDIES

Debris tank is full and check ball is

closed.

Drain or recycle water in debris tank. Dump debris tank.

Boom turret plugged.

Remove turret and clear blockage.

Vacuum system leak.

Inspect vacuum system for leaks, normally a high pitched

sound is heard. Some areas to check first are: Rear door seal,

tank closure seal, intake tube O-rings, portal gasket. Check to

see that gate valves are closed, such as rear drain, and valves

on the recycling system.

Blockage in the intake hose.

Disengage exhauster pump and evacuate the vacuum from the

tank. Inspect intake tubes. Remove the primary check valve

cover and inspect the ball check. Lower the boom all the way

to allow material to drop out through the hose. Pressure dis-

charge through boom hose.

Inadequate engine speed.

Check engine tachometer, adjust throttle cable, consult engine

manual. Check for correct gear.

Loose exhauster pump drive belt.

Tighten.

Faulty vacuum reading.

Replace gauge.

Exhauster pump malfunction.

Consult exhauster pump manual.

Sticking vacuum relief valves.

Check to determine if they open at 15” Hg.,

Clean/lubricate/replace if necessary.

TROUBLESHOOTING COMMON PROBLEMS

The following is a list of possible problems which may be encountered during the life of this machine. Probable

causes are listed in this section together with recommended solutions to these problems. If the resolution of these

problems or any other problems are not readily apparent, contact your local authorized X-Vac dealer.

Содержание X-Vac Hydro Excavator X15 Series
























































































Результаты поиска

Содержание X-Vac Hydro Excavator X15 Series

Отзывы:

Похожие инструкции для X-Vac Hydro Excavator X15 Series

Бренды по названию

Популярные бренды

Hi-Vac X-Vac Hydro Excavator X15 Series, Инструкция по эксплуатации, обслуживанию и ремонту

Результаты поиска

Содержание X-Vac Hydro Excavator X15 Series

Отзывы:

Похожие инструкции для X-Vac Hydro Excavator X15 Series

Бренды по названию

Популярные бренды