Hettich 4050674010009QG Скачать руководство пользователя страница 35

Страница: 35 / 38

AB1203EN_SA

Rev. 02 / 11.2022

35/38

25 Faults

If the fault cannot be eliminated with the help of the fault table, please inform Customer Service.

Please specify the type of centrifuge and the serial number. Both numbers can be found on the name plate of the
centrifuge.

Perform a MAINS RESET:



Switch off the mains switch (switch position "0").



Wait at least 10 seconds and then switch on the mains switch again (switch position "



").

Message / fault

Cause

Remedy

No display

No voltage
Mains input fuses defective.



Check distribution voltage.



Check mains power input fuse, refer
to Chapter "Change mains input
fuse".



Mains switch ON.

IMBALANCE

The rotor is unevenly loaded.



Open the lid after the rotor is at a
standstill.



Check the loading of the rotor, see
chapter "Loading the rotor".



Repeat the centrifugation run.

MAINS INTER

MAINS INTERRUPT

Power failure during the
centrifugation run. (The
centrifugation run was not finished.)



Open the lid after the rotor is at a
standstill.



Push

START
PULSE

button.



Repeat the centrifugation run if
necessary.

TACHO ERROR

1, 2

Failure of speed impulses during
operation.

LID ERROR

4.1 – 4.127

Error in lid locking or lid closure.

OVER SPEED

Rotation too fast



Perform a MAINS RESET when the
rotor has been stationary.

VERSION ERROR

Incorrect centrifuge model
recognized.
Error / defect electronics

UNDER SPEED

Rotation too slow

CTRL ERROR

22.1, 25.2

CRC ERROR

27.1

COM ERROR

31 – 36

FC ERROR

60,

61.1 – 61.21,

61.64 – 61.142

Error / defect electronics



Perform a MAINS RESET when the
rotor has been stationary.

FC ERROR

61.23

TACHO ERR

61.22

Speed measurement error



The device many not be switched
off as long as the rotation display
is lit up and rotating. Wait until the
symbol (lid locked) is displayed
(after approx. 120 seconds).
Afterwards, carry out a MAINS
RESET.

FC ERROR

61.153

Error / defect electronics



Perform a MAINS RESET.



Check the loading of the rotor, see
chapter "Loading the rotor".



Repeat the centrifugation run.

Содержание 4050674010009QG







































Результаты поиска

Содержание 4050674010009QG

Отзывы:

Похожие инструкции для 4050674010009QG

Бренды по названию

Популярные бренды

Hettich 4050674010009QG, Руководство по эксплуатации

Результаты поиска

Содержание 4050674010009QG

Отзывы:

Похожие инструкции для 4050674010009QG

Бренды по названию

Популярные бренды