background image

 

 

13 

Fig. 14 

    (18) 

      (17) 

      (24) 

  

PLUMBING INSTRUCTIONS   

 

 

1.  The helix is designed for a water supply line of 1” pipe. 

Plumb from pool return line with a 1” PVC pipe “stubbed up” 
at the deck positioned at the base of the ladder. Refer to 
Figure 1 on page 2.  Figure 1 is for reference only.  
Assembled slide should be placed in its correct location and 
the “stub up” location marked and installed before mounting 
the slide to the deck. “Stub up” should be dark grey PVC to 
match the plumbing assembly of the slide. Note: “Stub up” 
should extend above the deck 18” in height; it will be cut 
down later in the installation process.
 

 

2.  If a garden hose is to be used, a garden hose adapter fitting 

is included with the slide.  Assemble the pieces as shown in 
Figure 14 and attach to the end of the PVC plumbing 
assembly at the base of the ladder.  

 

3.  Proceed to the following section for ON-DECK MOUNTING.  

After the slide has been mounted to the deck, attach the 
“stub up” to the plumbing assembly installed in the ladder.   

 

4.  The helix can handle up to 20 gallons per minute.  Water 

flow to the main water supply is to be regulated using the ball 
valve (16) near the center of the ladder. The fountain feature 
can be regulated via the small ball valve just under the top of the ladder. Figure 13 shows the 
location of the small ball valve. 

 

5.  The fountain feature and the main water supply can be either used together or alone. 

a.  To use only the main water supply, shut off the small ball valve.  Adjust the large ball valve 

for the desired water flow. 

b.  To use only the fountain, shut off the large ball valve.  Adjust the small ball valve for desired 

flow. 

c.  To use both the fountain and the main water supply together, the large ball valve must be 

partially closed.  In general, closing the large ball valve more will increase the flow to the 
fountain.  Adjust the small and large ball valves to obtain the desired flow from each water 
feature.   

 

BROKEN OUT 
SECTION 
DETAIL A 

Fig. 13

 

SMALL BALL VALVE  
 

Содержание S.R. SMITH



















Отзывы: