background image

 

HEATSTORE AFTER SALES SERVICE 

 

 

SELF HELP 

 

If the unit is not working satisfactorily, make the following checks before calling out the installer.         
Any one of these adjustments could restore the performance. 

 

Symptom 

Cause 

What to do 

Little or no water flow 

The main water supply is turned 
off. 

Turn on the main supply fully at the 
stop valve.  Set up unit as per 

commissioning instructions. 

Cold water only 
- neon light off 

The main water supply is not 
turned on enough. 

Turn on the main supply fully at the 
stop valve. 

Water too cold 

- neon light on 

The water flow rate is too high. 

 

The inlet water temperature has 

dropped. 

Adjust the service valve (see page 7). 

 

Adjust the service valve (see page 7). 

 

For a shower, adjust the spray pattern 

available on the multi-mode handset. 

Water flow too low, or 
temperature too high 

The main water supply is too low 
 

 

 

The hot tap is not fully open. 

Increase the supply water flow.                             
Make sure that the service valve is 

correctly adjusted. 

 

Adjust the service valve so that the 
water is at the right temperature with 
the tap fully open (see page 7). 

 

Always turn the hot tap fully on. 

Water goes from hot        

to cold 

The water flow or pressure is too 

low, and the thermal cut-out is 
operating. 

 

A second outlet has been turned 
on. 

Increase the supply water flow 

Make sure that the service valve is 
correctly adjusted. 

 

Do not use the basin whilst using the 
shower. 

Shower spray pattern 
deteriorates 

The shower handset is clogged. 

Clean the handset using a descaling 
solution if required (see page 9). 

 

We offer a technical advisory service on the telephone to installers and other customers with 
problems in the field. 

 

RING: “0117 923 5375”    or    E-MAIL: “[email protected]” 

 

Remember to quote the exact type of unit, as written on the front of the shower and on this leaflet.                                                     
The model and serial number are located on the bottom face of the shower. 
Make a note of those numbers here, and be sure to quote them if you call for advice.  

 

Model Number:  _ _ _ _ _ _ _ _ _ _ _ _ _   Serial Number:  _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

 

 

Note: You may be charged for a service call if you do not have the serial number.

 

 

 

 

Please Note:- The fitting of Spare Parts must be supervised by a suitably qualified person. 

 

Chrome and White Shower Mixer Unit Complete with full accessories 

 

Including 3 position multi-function handset  

 

 

 

 

Catalogue No. 3615 

 

For further details, including a comprehensive list off accessories and spare parts, 
contact Heatstore Sales Hotline 0117 923 5375 

WHAT TO DO IF THINGS GO WRONG (1) 

         ADDITIONAL ACCESSORIES AND COMMON SPARE PARTS     

Содержание Multiflow 10.8kW













Отзывы: