Heatilator ECO-ADV-WS18 Скачать руководство пользователя

Страница: 1 / 46

7056-138L • August 23, 2019

www.heatilatorecochoice.com

NOTICE: DO NOT DISCARD THIS MANUAL

Consumer Care 1-877-427-3316 - Prior to calling, please

have the model and serial number of the unit you are

calling about. This information can be found at the front of

the unit.

WARNING

If the information in these instructions is

not followed exactly, a fire could result

causing property damage, personal injury,

or death.

•

Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

•

Do not over-fire - If appliance or chimney connector

glows, you are over-firing. Over-firing will void

your warranty.

• Comply with all minimum clearances to combustibles

as specified. Failure to comply may cause house fire.

WARNING

Fire Risk.

For use with solid wood fuel only.

Other fuels may over-fire and generate

poisonous gases (i.e. carbon monoxide).

Installation and service of this appliance should be performed by

qualified personnel. Hearth & Home Technologies recommends

HHT Factory Trained or NFI certified professionals.

HOT SURFACES!

Glass and other surfaces are hot during

operation AND cool down.

WARNING

Hot glass and appliance will cause burns.

• Do not touch glass until it is cooled

• Use leather gloves when reloading fuel

• NEVER allow children to touch glass

• Keep children away

•

CAREFULLY SUPERVISE children in same room

as appliance.

• Alert children and adults to hazards of

high temperatures

• High temperatures may ignite clothing or other

flammable materials.

• Keep clothing, furniture, draperies and other

flammable materials away.

NOTE:

To obtain a French translation of this

manual, please contact your dealer or visit

www.heatilatorecochoice.com

REMARQUE :

Pour obtenir une traduction française

de ce manuel, s’il vous plaît

contacter votre revendeur ou visitez

www.heatilatorecochoice.com

Owner’s Manual

Installation and Operation

INSTALLER: Leave this manual with party responsible for use and operation.

OWNER: Retain this manual for future reference.

Contact your dealer with questions on installation, operation, or service.

WOOD BURNING APPLIANCE

MODEL(S):

ECO-ADV-WS18

Содержание ECO-ADV-WS18















































Результаты поиска

Содержание ECO-ADV-WS18

Отзывы:

Похожие инструкции для ECO-ADV-WS18

Бренды по названию

Популярные бренды

Heatilator ECO-ADV-WS18, Руководство пользователя по установке и эксплуатации

Результаты поиска

Содержание ECO-ADV-WS18

Отзывы:

Похожие инструкции для ECO-ADV-WS18

Бренды по названию

Популярные бренды