Heatilator CNXT4236IH CNXT4842IH Скачать руководство пользователя | Manualshive

Страница: 50 / 92

background image

50

Heatilator • Caliber CNXT Series • 4047-132 Rev P • 11/07

Child Proof Mode
To Enter Child Proof Mode:

• Press the Up Arrow Button twice and Down Arrow Button

once. The unit will send out three beeps and an indicator
in the LCD panel will show that the child proof is on.

To Leave Child Proof Mode:

• Press the Up Arrow Button twice and Donw Arrow Button

once. The unit will send out three beeps and the indicator
in the LCD panel showing that child proof is on will
disappear.

Note:

When in Child Proof Mode, only the arrow buttons

will have functionality. Unit can enter Child Proof when the

fi

replace is on or off.

Cold Climate Button

• Button Press: Turns on Climate Control
• Button Press: Turns off Climate Control

This allows the pilot

fl

ame to stay lit when activated. A ben-

e

fi

t of this is reduced condensation on the glass at start-up

in colder climate conditions.

Operation Under Battery Power

A switch on the control box allows for battery power under
no-power conditions (see Figure 10.9). By controlling the
power supply with this switch, the batteries are supplying
power only when needed, thus extending battery life. The
switch also provides a convenient means for switching to
battery power should there be a loss of 110 VAC power to
the control box.

• In the event of a power failure, switch the battery operation

switch to the “Battery ON” position.

• The

fi

replace can now be turned on and off with the ON/

OFF rocker switch located near the gas valve.

• The wall switch functions will not operate under battery

power.

• Under battery control the only available function is

fl

ame

“ON” and “OFF” in the high position.

• To maximize battery life, and to restore full function

capability of the wall switch,

fl

ip switch to “OFF” position

after 120 VAC power is restored.

K. Wall Switch Button Operation

(Refer to Figure 10.8.)

Flame

Button

• Button Press: Unit On / Flames High, turns on auxilary

power

• Button Press: Flames Low
• Button Press: Unit Off / Flames Off, turns off auxilary

power

Fan / Blower Button

•  Button Press: Fan High (“3”)
•  Button Press: Fan Medium (“2”)
•  Button Press: Fan Low (“1”)
•  Button Press: Fan Off

Temperature

Button

• Button Press will toggle between Automatic and Manual

Operation.

• Press and Hold the button for 3 seconds to toggle between

Fahrenheit and Centigrade Temperature Display.

Automatic Operation: Controller will monitor temperature
and control unit according to the set point.

Manual Operation: Controller will not automatically change
settings.

SET Set Temperature Button

•  Button Press: Displays Set Point
•  Use UP and Down Arrows to adjust set point
•  Press Set Button to store new set point

Temperature Set Point can be adjusted between the ranges
of 45-90° Fahrenheit or 7-32° Centigrade.

Note:

The controller will turn off the

fi

replace at 2° F over

set point and turn it back on at 2° F below set point.

Up and Down Arrows

• Push to adjust set point temperature under automatic

control.

AUX Auxilary

Button

• Button Press: Turns on auxilary power
• Button Press: Turns off auxilary power

Can be operated independently of all functions.

«
...
48
49
50
51
52
...
»

Содержание CNXT4236IH CNXT4842IH





























































































Отзывы:

Нет отзывов

Похожие инструкции для CNXT4236IH CNXT4842IH

Бренд: Napoleon Страницы: 56

Бренд: Napoleon Страницы: 2

Бренд: Napoleon Страницы: 40

Бренд: Napoleon Страницы: 16

Castlemore GDS26N

Бренд: Napoleon Страницы: 32

Бренд: Napoleon Страницы: 28

Бренд: Napoleon Страницы: 64

Бренд: Napoleon Страницы: 34

Бренд: Napoleon Страницы: 2

Ascent Linear Series

Бренд: Napoleon Страницы: 128

Бренд: Napoleon Страницы: 2

Бренд: Napoleon Страницы: 132

Бренд: Napoleon Страницы: 48

Бренд: Napoleon Страницы: 48

Бренд: Napoleon Страницы: 24

Бренд: Napoleon Страницы: 31

Бренд: Napoleon Страницы: 12

Бренд: Unigas Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды