background image

3

PRODUCT FEATURES

SAFETY  DEVICE

A  standard  requirement for all vent-free  room
heaters, this  heater has a pilot  with  an  Oxygen
Depletion  Sensor(ODS)  safety  shutoff  system.
The ODS/pilot  shuts  off  the heater  if  there  is
not  enough  fresh  air.

PIEZO  IGNITION  SYSTEM

This  heater  is  equipped  with  a  piezo  ignitor.
This  system  requires  no  matches, batteries, or
other  sources  to  light  heater.

THERMOSTATIC  HEAT
CONTROL  ON  THERMOSTAT
MODELS

These  heaters  have  a  control  valve  with  a
thermostat  sensing  bulb. This  results  in  the
greatest  heater  comfort  and  may  result  in
lower  gas  bills.

Figure1-Vent-Free  Natural  Gas  Heater

Water vapor is a by-product of gas combustion.An
unvented room heater productes approximately one (1)
ounce (30ml) of water for every 1,000 BTU’s (.3KW’s) of
gas input per hour.
U n v e n t e d   r o o m   h e a t e r s   a r e   r e c o m m e n d e d   a s
supplemental heat (a room) rather than a primary heat
source (an entire house) .In most supplemental heat
applications, the water vapor does not create a problem.
In most applications, the water vapor enhances the low
humidity atmosphere experienced during cold weather.

WATER VAPOR: A BY-PRODUCT OF UNVENTED ROOM HEATERS

The following steps will help insure that water vapor
does not become a problem.
1. Be sure the heater is sized properly for the
application, including ample combustion air and
circulation air.
2. If  high humidity is experienced, a dehumidifier may
be used to help lower the water vapor content of the
air.
3. Do not use an unvented room heater as the primary
heat source.

LOCAL  CODES

Install  and  use  heater  with  care. Follow  all  local
codes. In  the  absence  of  local  codes, use   the
latest  edition  of  

National  Fuel  Gas  Code

ANSZ223.1

,also  known  as  NFPA  54*.

*Available  from :
         American  National  Standards Institute, Inc.

1430  Broadway

         New York, NY 10018

National  Fire  Protection  Association, Inc.

  Batterymarch  Park

Quincy, MA  02269

UNPACKING

1. Remove  heater  from  carton.
2. Remove  all  protective   packaging  applied  to

     heater  for  shipment.
3. Check  heater  for  any  shipping  damage. If  heater
    is  damaged. promptly  inform  dealer  where  you
     bought  heater.

QUALIFIED  INSTALLING  AGENCY

Installation and replacement of gas piping, gas uti-

lization equipment or accessories and repair and

servicing of equipment shall be performed only by a

qualified agency. The term “qualified agency” means

any individual, firm, corporation, or company that ei-

ther in person or through a representative is en-

gaged in and is responsible for (a) the installation,

testing, or replacement of gas piping or (b) the

connection, installation,  testing, repair, or servicing

of equipment; that is experienced in such work; that

is familiar with all precautions required, and that

has complied with all the requirements of the au-

thority having jurisdiction.

State of Massachusetts: The installation must be

made by a licensed plumber or gas fitter in the

Commonwealth of  Massachusetts.

Sellers of unvented propane or natural gas-fired

supplemental room heaters shall provide to each

purchaser a copy of 527 CMR 30 upon sale of the

unit.

In the state of Massachusetts, unvented  propane

or nature gas-fired space heaters shall be prohib-

ited in bedrooms and bathrooms.

Heater
Cabinet

Burners

Grill

Control
Knob

Ignitor
Button

Lower
Front
Panel

Содержание HR18MN-1





























Отзывы: