background image

17

Inspect and properly tighten all parts of the elliptical

exerciser regularly. Replace any worn parts immedi-

ately.

CONSOLE TROUBLESHOOTING

If the console displays become dim, the batteries

should be replaced; most console problems are the

result of low batteries. See assembly step 7 on page 9

for replacement instructions. If the handgrip pulse sen-

sor does not function properly, see step 5 on page 13.

HOW TO REMOVE THE SHIELDS AND THE

FLYWHEEL COVERS

The Left and Right Shields (15, 16) must be removed

before the reed switch or the drive belt can be

adjusted. To remove the Shields, remove the indicated

Screws (71, 72).

Note which hole each Screw is

removed from; the Screws must be reattached in

the same holes.

Carefully separate and remove the

Shields.

Next, the Right

and Left

Flywheel Covers

(18, 19) must be

removed.

Remove the indi-

cated Screws

(48, 69) from the

Flywheel Covers.

Note which

hole each

Screw is

removed from;

the Screws must be reattached in the same holes.

Carefully separate and remove the Flywheel Covers.

HOW TO ADJUST THE REED SWITCH

If the console does not display correct feedback, the

reed switch should be adjusted. To adjust the reed

switch, first see the instructions at the left and remove

the shields and the flywheel covers.

Next, see the drawing below. Locate the Reed Switch

(55). Turn the Pulley (38) until a Magnet (37) is

aligned with the Reed Switch. Loosen, but do not

remove, the indicated Screw (72). Slide the Reed

Switch slightly closer to or away from the Magnet, and

then retighten the Screw. Turn the Pulley for a

moment. Repeat these actions until the console dis-

plays correct feedback. Then, reattach the shields and

the flywheel covers.

HOW TO ADJUST THE DRIVE BELT

If you can feel the pedals slip while you are pedaling,

even when the resistance is adjusted to the highest

setting, the drive belt may need to be adjusted. To

adjust the drive belt, first see the instructions at the

left and remove the shields and the flywheel covers.

Next, see the drawing above. Loosen the indicated

Jam Nut (76). Tighten the indicated Screw (74) until

the Drive Belt (39) is properly tightened, and then

retighten the Jam Nut (76). Then, reattach the shields

and the flywheel covers.

MAINTENANCE AND TROUBLESHOOTING

72

72

71

71

48

15

16

19

18

48

69

69

69

74

76

39

55

37

38

72

Содержание H70e Elliptical

























Отзывы: