HB-THERM CLEAN-5 Скачать руководство пользователя страница 84

Страница: 84 / 97

HB-CL2

Cleaning Unit

Faults

O8305-EN 2022-01

10 Faults

The following chapter describes possible causes of malfunctions
and what to do to remove them.

In the case of increased disturbances, reduce the maintenance
intervals according to the actual burden.

In the case of faults, which can not be remedied by the following
instructions, contact the HB-Therm representative
(



www.hb-therm.ch

). For error diagnoses, service information

can be saved to a USB data carrier and sent to the HB-Therm
representative (



page 70).

10.1 Safety

Personnel



Tasks for troubleshooting described here can be performed by

the operator, unless otherwise indicated.



Some tasks must only be carried out by qualified personnel or

by the manufacturer exclusively. If this is required, it is pointed
out separately in the description of the respective faults.



As a rule, work on the electrical system must only be carried out

by certified electricians.



Work on the hydraulic system must only be carried out by

qualified hydraulics technicians.

Personal protective equipment

Wear the following protective equipment for all maintenance/repair
work:



Safety goggles



Protective gloves



Safety shoes



Protective clothing

NOTE!

For specific work, the warning notices in this
chapter draw special attention to further protective
equipment.

Special dangers

The following dangers exist:



Danger of fatal injury by electric current.



Danger of injury from aggressive working materials.



Danger of crushing due to rolling away or tipping.

Содержание CLEAN-5


































































































Результаты поиска

Содержание CLEAN-5

Отзывы:

Похожие инструкции для CLEAN-5

Бренды по названию

Популярные бренды

HB-THERM CLEAN-5, Инструкция по эксплуатации

Результаты поиска

Содержание CLEAN-5

Отзывы:

Похожие инструкции для CLEAN-5

Бренды по названию

Популярные бренды