13
For one speed pumps, this is the second filter timeclock.
For two speed or variable speed pumps, this timeclock will set the normal time period for
filter pump
low speed operation
(the word “Filter T2” in the display will be replaced with “Filter Lo”). If the filter
pump is off for more than 30 seconds, the pump will first turn on at high speed for 3 minutes to prime
and establish water flow. Afterwards, it will drop down to low speed for the remainder of the programmed
low speed time period. While this time clock will override the high speed timeclock (see above), there
are several reasons why the pump will automatically switch to high speed operation during this
programmed time period. These include manual operation, spa operation, or heating operation.
This menu is only available if the system has been setup for “pool and spa-std”. During the programmed
spa time, the Aqua Plus 16v will move the pool/spa valves into the “spa-only” position and turn on the
filter pump. The heater will automatically heat the spa up to the programmed spa temperature. This
programmed spa operation will take precedence over all other automatic functions, only manual
operation of the filter button or pool/spa valve button will override this function.
If your pool has a separate jet pump or blower controlled by Aux1 and/or Aux2 , you will have to
program those separately.
This menu will appear only if the Lights are configured for timeclock. The lights will turn on and off at
the designated times. The only override on this function is manual on/off control by the “Lights”
button.
This menu will appear only if the Lights are configured for countdown timer. This setting is the time
after you manually turn on the lights until the Aqua Plus 16v automatically turns off the lights. You
can also manually turn off the lights at an earlier time by pressing the LIGHTS button.
34
Set Day and Time
Wednesday 10:37P
Adjust time setting
Move between start and stop times & to previous/next menu item
Filter T2
8:30A to 4:00P
-all
Filter T2-wkend
8:30A to 4:00P
Filter T2-wkday
8:30A to 4:00P
Adjust time setting
Adjust time setting
Move between start and stop times & to previous/next menu item
Move between start and stop times & to previous/next menu item
or
Set Day and Time
Wednesday 10:37P
Adjust time setting
Move between start and stop times & to previous/next menu item
Spa-all
6:00P to 9:00P
Spa-wkend
6:00P to 9:00P
Spa-wkday
6:00P to 9:00P
Adjust time setting
Adjust time setting
Move between start and stop times & to previous/next menu item
Move between start and stop times & to previous/next menu item
or
Set Day and Time
Wednesday 10:37P
Adjust time setting
Move between start and stop times & to previous/next menu item
Lights-all
8:00P to 11:00P
Lights-wkend
8:00P to 11:00P
Lights-wkday
8:00P to 11:00P
Adjust time setting
Adjust time setting
Move between start and stop times & to previous/next menu item
Move between start and stop times & to previous/next menu item
or
or
Lights-CountDn
0:20
Adjust time setting (Manual On/Off, 0:05, 0:10, 0:015...)
Move to previous/next menu item
Note: Separate chlorinator output levels for the pool and spa must be set. If the valves are in
the pool-only or spa spillover positions, then the chlorinator will operate per the pool setting.
If the valves are in the spa-only position then the chlorinator will operate according to the spa
setting. The actual amount of chlorine introduced into the pool/spa is determined by: this
output setting, the amount of time the filter pump is running, the water temperature, and the
amount of salt in the water. Also see Start/Stop Supechlorination below.
Start/Stop Superchlorination
1. Press the “MENU” button repeatedly until “Settings Menu” is displayed
2. Press the “>” button repeatedly until “Super Chlorinate” is displayed.
3. The display will show whether superchlorination is “on” or “off”.
4. Press “+” or “-” to toggle between “on” and “off”
Note: Once started, superchlorination will run for the programmed number of hours (Timers
Menu/Super Chlorinate Hours) or until you manually turn it off. Superchlorination may be
temporarily interrupted for a programmed spa operation.
Program a Timeclock
1. Press the “MENU” button repeatedly until “Timers Menu” is displayed
2. Press the “>” button repeatedly until the “xxx—all days” or “xxx—weekends” is displayed.
3. Use the “+” and “-“ buttons to set the desired start time, then press “>” to switch to the off time. Use
the “+” and “-“ buttons to adjust the off time. If you are setting the “weekend” timeclock, press “>” to
go to the “weekday” settings.
Note: During the programmed time, there may be other automatic or manual operations that
prevent the relay/valve from operating—see a more detailed discussion under Automatic Sys-
tem Operation/Timers Menu/Aux Timeclock or in Troubleshooting/Diagnostic Information.
Program a Countdown Timer
1. Press the “MENU” button repeatedly until “Timers Menu” is displayed
2. Press the “>” button repeatedly until the “xxx—CountDn” is displayed.
3. Use the “+” and “-“ buttons to set the desired timer period.
Note: A setting of 0:00 will display as “Manual On/Off.” The countdown automatic turn off
function is disabled by manual operation is still permitted. There may be other automatic or
manual operations that prevent the relay/valve from operating—see a more detailed discussion
under Automatic System Operation/Timers Menu/Aux Timeclock or in Troubleshooting/Diag-
nostic Information.
Enter/Exit Service (or Service—Timed) Mode
1. Go to Aqua Plus 16v main unit (normally mounted near the pool equipment)
2. Pressing the “Service” button rotates through normal operation (red LED off), service mode (red
LED on continuously) and service-timed mode (red LED flashing).
Note: This operation can only be performed at the main Aqua Plus 16v unit. Both “Service”
and “Service-Timed” disable all automatic programmed operations and allow manual opera-
tion from the main unit only. The buttons on the remote display/keypads will still be able to turn
equipment off in case of an emergency, but will not turn any equipment on. If the system is in
“Serviced-Timed” it will automatically switch back to normal operation at the end of the time
period.
