Hayward Aqua Plus 16v Скачать руководство пользователя страница 1

Quarterly

       Monthly

       Weekly

Free Chlorine      1.0 - 3.0 ppm       
         
       

        pH                   7.2 - 7.8

Raise desired output % to

increase, lower desired output %

to decrease -OR- increase or

decrease pump filtration time.

Too low -  add soda ash.

Too high - add muriatic acid

Alkalinity           80 - 120 ppm
                         

                        

   Salt             2700 - 3400 ppm   Add salt as required to increase.

 Add baking soda to increase.

     Stabilizer        60 - 80 ppm         Add cyanuric acid to increase.

     
     Calcium         200 - 400 ppm      Add calcium to increase.   

                          
                                                        
Electrolytic Cell   inspect & clean    Refer to section in manual.

TEST         IDEAL RANGE          ADJUSTMENT REQUIRED

Drain and add water to decrease.

Add acid as required to decrease.

092457 RevB

Copyright © 2010 Hayward

620 Division St.
Elizabeth, NJ  07207

Automation and Chlorination

Operation Manual

for model

PL-PLUS-16V

Aqua Plus 16v

www.haywardnet.com

Содержание Aqua Plus 16v



























Отзывы: