background image

SUPPLEMENTAL LIMITED WARRANTY.

Hatz Diesel of America, Inc. hereinafter referred to as “HATZ” warrants each of the
above-listed parts when installed in a new engine sold by Hatz to be free from defects in
material and workmanship under normal use and service, only under the named warranty
coverage conditions, after the date of delivery to the original retail purchaser and Hatz
will at their option, repair or replace at Hatz's sales headquarters, or at a point designated
by Hatz, any part or parts which shall appear to the satisfaction of Hatz upon inspection at
such point, to have been defective in material or workmanship.

•  Any warranted part which is scheduled for replacement as required maintenance is 

warranted for the period of time up to the first scheduled replacement point for that
part.

•  Any replacement part which is equivalent in performance and durability may be used in

non-warranty maintenance or repairs and will not reduce the overall engine warrranty 
obligations of Hatz. However, Hatz is not responsible for failure of such replacement
parts or failure of any other parts directly caused by failure of such replacement parts.

•  This warranty does not obligate Hatz to bear any transportation charges in connection

with the repair or replacement of defective parts. This warranty is transferrable to 
subsequent owners, only under the named warranty coverage conditions.

•  In order to obtain service under this warranty, the retail purchaser should contact Hatz

Diesel of America, Inc. at (262)-544-0254 for information and the nearest service 
center. The retail purchaser will not be charged for diagnostic labor which leads to the 
determination that a warranted part is defective, nor for the repair or replacement of 
warranted parts if the work is performed at an authorized Hatz service center. If other 
engine components are damaged due to a failure of the above-listed warranted parts 
still under warranty, these other engine components will also be repaired or replaced at 
no charge.

•  This warranty shall not apply to any engine which shall have been installed or 

operated in a manner not recommended by Hatz, nor to any engine which shall have
been repaired, altered, neglected, or used in any way which, in the opinion of Hatz, 
adversely affects its performance, nor to any engine in which parts not authorized by
Hatz have been used, which parts or the use of which have damaged or caused defects
in or otherwise adversely affected the engine or its performance, nor to normal 
maintenance service or replacement of normal service items.

Hatz reserves the right to modify, alter, and improve any engine or parts without incurring
any obligation to replace any engine or parts previously sold with such modified, altered,
or improved engine or parts.

50

Содержание 2W35







































































Отзывы: