Harmonic Drive FHA Series Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 51

background image

31

Chapter 3 Installing the FHA-C actuator

3-1 Receiving Inspection

Check the following when products are received.

• Inspection procedure

(1) Check the shipping container and item for any damage which may have been caused during transportation.

If the item is damaged, immediately report the damage to the dealer it was purchased from.

(2) A label is attached on the right side of the FHA actuator. Confirm the products you ordered by comparing with

the model on the [TYPE] line of the label. If it is different, immediately contact the dealer it was purchased from.

The model code is interpreted as follows:

Refer the section 1-2 in this manual for the detail of the model codes.

(3) On the label of the HA-655 or HA-675 driver, the model code of the FHA-C series actuator to be driven is indicated on the

[ADJUSTED FOR USE WITH] line. Match the actuator with its driver so as not to confuse the item with the other actuators,.

Only connect the actuator specified on the driver label.

The drivers have been tuned for the actuator specified on the driver label.

Wrong combination of drivers and FHA actuators may cause low torque

problems or over current that may cause physical injury and fire.

(4) A model of the driver is marked on the [TYPE] line of the label.

The last three digits indicate the voltage of power supply.

200: 3-phase or single phase 200V

100: single phase 100V

If the voltage to be supplied is different from the label voltage,

immediately contact the dealer it was purchased from.

Do not connect a supply voltage other than the voltage specified on the label.

The wrong power supply voltage may damage the driver resulting in physical injury and fire.

FHA- 17 C-50-E

250

-

AC servo actuator FHA series

Frame size: 17, 25, 32, 40

Design version

Reduction ratio of harmonic drive

®

gearing

Encoder specifications

Encoder resolution

Option

-

!

CAUTION

!

CAUTION

Chapter 3 Installing the FHA actuator

«
...
32
33
34
35
36
...
»

Содержание FHA Series




















































Отзывы:

Нет отзывов

Похожие инструкции для FHA Series

Бренд: CAME Страницы: 12

Бренд: CAME Страницы: 16

Бренд: Ultrak Страницы: 41

Бренд: Zander Aachen Страницы: 10

Бренд: Taie Страницы: 66

Бренд: ZirbenLüfter Страницы: 36

ACTIVE DRIVER M/M 1.1

Бренд: DAB Страницы: 10

Бренд: d&b audiotechnik Страницы: 3

ACTIVE DRIVER M/M 1.1

Бренд: DAB PUMPS Страницы: 38

Бренд: Eaton Страницы: 100

Бренд: Uclear Страницы: 40

Бренд: Jabra Страницы: 3

Бренд: Wang Страницы: 68

Бренд: NAVITAS Страницы: 14

Extinguishing Control Panel BC06-2EXT

Бренд: LST Страницы: 4

Бренд: Desoutter Страницы: 74

Бренд: jablotron Страницы: 2

Бренд: Anthem Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды