Harman Kardon DIGITAL LOUNGE 632 Скачать руководство пользователя страница 19

Страница: 19 / 54

INSTALLATION AND CONNECTIONS

ENGLISH

Installation and Connections

Important Note

Please open the Harman Kardon Digital Lounge
Accessory Tool Kit before opening any of the
other system components. The Kit contains two
pairs of gloves, that can be used to unpack the
LCD screen without damaging its frame nor
leaving fingerprints on it.

After unpacking the different system components,
and placing them on a solid surface capable of
supporting their weight, you will need to make the
connections to your audio and video equipment.

Equipment Connections

We recommend that you use the supplied cables
when making connections to source equipment
and high quality interconnect cables to additional
equipment to preserve the integrity of the
signals.

When making connections to audio source
equipment or speakers it is always a good
practice to unplug the units from the AC wall
outlet. This prevents any possibility of
accidentally sending audio or transient signals to
the speakers that may damage them.

Making the necessary connections to the Digital
Lounge system is done in five easy steps.

1. Connect the front, center and surround speaker
outputs

to the respective speakers.

Cables that are run inside walls should have the
appropriate markings to indicate listing with any
appropriate testing agency standards. Questions
about running cables inside walls should be
referred to your installer or a licensed electrician
who is familiar with the applicable local building
codes in your area.

When connecting wires to the speakers, be
certain to observe proper polarity. Note that the
positive (+) terminal of each speaker connection
now carries a specific color code. However, most
speakers will still use a red terminal for the
postive (+) connection. Con nect the “negative”
or “black” wire to the same terminal on both the
receiver and the speaker.

We also recommend that the length of cable
used to connect speaker pairs be identical.
For example, use the same length piece of
cable to connect the front-left and front-right
or surround-left and surround-right speakers,
even if the speakers are a different distance
from the Digital Lounge system controller.

2. Connections to the subwoofer are made via a
line level audio connection from the

Subwoofer

Output

to the line-level SUB input (purple)

of the subwoofer. Connect at the same time the

Subwoofer Trigger Output

to the Trigger

Input of the subwoofer.

3. Connect the supplied FM antenna to the

(75 ohm)

connection

. The FM antenna may

be an external roof antenna, an inside powered
or wire lead antenna or a connection from a
cable system. Note that if the antenna or connec-
tion uses 300-ohm twin-lead cable, you should
use a 300-ohm-to-75-ohm adapter to make the
connection.

4. Your system comes with an combined
HDMI/SP-DIF/Remote in/out cable to make a dig-
ital video connection over HDMI and digital
audio connection from the TV to the DVD re -
ceiver. Connect the HDMI connector on one end
of the wire to the HDMI Output

of the receiv-

er and the other end to the HDMI Input

the screen. Connect the Coaxial Digital connector
on one end of the cable to the Coaxial Digital
Input

of the receiver and the other end to the

Coaxial Digital Output

of the screen.

Connect one end of the remote connector (the
single pin connector) to the Remote Input of the
screen and the other end to the Remote Input of
the DVD Receiver. Please note that you may run
the remote signal both ways. If you decide that it
is easiest for you to control both screen and
receiver by pointing the remote control towards
the screen, plug the remote cable into the
Remote Control Out of the screen and into the
Remote Control In of the receiver. If your setup
makes it more practical to aim the remote at the
receiver to control both receiver and screen, plug
the remote cable into the Remote Control Out of
the receiver and into the Remote Control In of
the screen.

5. If you use a standard analog TV antenna, con-
nect to the Antenna Input

on the rear panel

of the screen. In case you use a DVB-T antenna,
connect that one to the DVB-T Input

on the

rear panel of the screen.

All necessary connections are now made. If you
have additional source components to add,
please refer to the next paragraphs. If not, please
continue with the next chapter of the manual.

Optional Analog Set Top or Cable
Box Connections

If you do not use an aerial antenna but a set top
box or cable box to watch TV, please follow the
instructions below to connect these products.

SCART

If you decide to connect your set top or cable box
to your system using a Scart cable, connect the
Scart output of the set top or cable box to one of
the Scart Inputs

on the rear panel of the

screen.

YUV/Component

If you decide to connect your set top or cable box
to your system using a YUV or Component cable,
connect the YUV outputs of the set top or cable
box to the YUV Inputs

on the rear panel of

the screen. At the same time connect the analog
audio outputs of the box to the Audio Input for
Component Video Jacks

on the rear panel of

the screen, or the digital output of the box to the
Coaxial Digital Input

S-Video

If you decide to connect your set top or cable box
to your system using an S-Video cable, connect
the S-Video output of the set top or cable box to
the S-Video Input

on the rear panel of the

screen. At the same time connect the analog
audio outputs of the box to the Audio Input for
S-Video Jacks

on the rear panel of the screen,

or the digital output of the box to the Coaxial
Digital Input

Composite

If you decide to connect your set top or cable box
to your system using a Composite cable, connect
the Composite output of the set top or cable box
to the Composite/CVBS Input

on the rear

panel of the screen. At the same time connect
the analog audio outputs of the box to the Audio
Input for Component Video Jacks

on the rear

panel of the screen, or the digital output of the
box to the Coaxial Digital Input

Important Note:

The

Coaxial Digital Input

of the screen will accept only 2-channel PCM

signals (see item

on page 13). To listen to the

multichannel sound from an optical digital out-
put of any external source you can connect it to
the

Optical Input