14
INSTALLATION AND CONNECTIONS
After unpacking the unit, and placing it on a solid
surface capable of supporting its weight, you will
need to make the connections to your audio and
video equipment.
Before starting to connect your AVR 745 to the
source devices, display device, speakers and other
components in your system, you should also
unpack the TC 30 remote, which is found in the
separate box inside the AVR 745 carton. So that
the TC 30 is ready when you begin the system
configuration process, install the battery, connect
the charger and place the remote in the charging
cradle, as it takes approximately twelve hours for
the battery to fully charge.
Audio Equipment Connections
We recommend that you use high-quality inter-
connect cables when making connections to
source equipment and recorders to preserve the
integrity of the signals.
When making connections to audio source
equipment or speakers it is always a good
practice to unplug the unit from the AC wall
outlet. This prevents any possibility of
accidentally sending audio or transient signals to
the speakers that may damage them.
1. Connect the analog output of a CD player to
the
CD
inputs
.
NOTE:
When the CD player has both fixed and
variable audio outputs it is best to use the fixed
output unless you find that the input to the
receiver is so low that the sound is noisy, or so
high that the signal is distorted.
2. Connect the analog Play/Out jacks of a cas-
sette deck, MD, CD-R or other audio recorder to
the
Tape Input
jacks
. Connect the analog
Record/In jacks on the recorder to the
Tape
Output
jacks
on the AVR.
3. Connect the digital output of any digital
sources such as a CD or DVD changer or player,
advanced video game, a digital satellite receiver,
HDTV tuner or digital cable set-top box or the
output of a compatible computer sound card to
the
Optical
and
Coaxial Digital Inputs
" #
*Ó
.
4. Connect the
Coaxial or Optical Digital
Outputs
on the rear panel of the AVR to the
matching digital input connections on a CD-R or
MiniDisc recorder.
5. Assemble the AM Loop Antenna supplied with
the unit as shown below. Connect it to the
AM
and
GND
screw terminals
.
6. Connect the supplied FM antenna to the
FM
(75 ohm)
connection
. The FM antenna may
be an external roof antenna, an inside powered
or wire lead antenna or a connection from a
cable system. Note that if the antenna or connec-
tion uses 300-ohm twin-lead cable, you should
use a 300-ohm-to-75-ohm adapter to make the
connection.
7. Connect the front, center and surround
speaker outputs
'
to the respective
speakers.
To ensure that all the audio signals are carried to
your speakers without loss of clarity or resoluti-
on, we suggest that you use high-quality speaker
cable. Many brands of cable are available and
the choice of cable may be influenced by the
distance between your speakers and the receiver,
the type of speakers you use, personal prefer-
ences and other factors. Your dealer or installer is
a valuable resource to consult in selecting the
proper cable.
Regardless of the brand of cable selected, we
recommend that you use a cable constructed of
fine, multistrand copper with an area greater than
2 mm
2
.
Cable with an area of 1.5 mm
2
may be used for
short runs of less than 4 m. We do not recom-
mend that you use cables with an area less than
1 mm
2
due to the power loss and degradation in
performance that will occur.
Cables that are run inside walls should have the
appropriate markings to indicate listing with any
appropriate testing agency standards. Questions
about running cables inside walls should be
referred to your installer or a licensed electrician
who is familiar with the applicable local building
codes in your area.
When connecting wires to the speakers, be cer-
tain to observe proper polarity. Note that the
positive (+) terminal of each speaker connection
now carries a specific color code as noted on
page 7. However, most speakers will still use a
red terminal for the postive (+) connection. Con-
nect the “negative” or “black” wire to the same
terminal on both the receiver and the speaker.
NOTE:
While most speaker manufacturers
adhere to an industry convention of using black
terminals for negative and red ones for positive,
some manufacturers may vary from this configu-
ration. To assure proper phase and optimal per-
formance, consult the identification plate on your
speaker or the speaker’s manual to verify polarity.
If you do not know the polarity of your speaker,
ask your dealer for advice before proceeding, or
consult the speaker’s manufacturer.
We also recommend that the length of cable
used to connect speaker pairs be identical. For
example, use the same length piece of cable to
connect the front-left and front-right or sur-
round-left and surround-right speakers, even if
the speakers are a different distance from the
AVR.
8. Connections to a single subwoofer are normal-
ly made via a line level audio connection from
the
Subwoofer Output
to the line-level
input of a subwoofer with a built-in amplifier.
When a passive subwoofer is used, the connec-
tion first goes to a power amplifier, which will be
connected to one or more subwoofer speakers. If
you are using a powered subwoofer that does
not have line-level input connections, follow the
instructions furnished with the speaker for con-
nection information.
If your system uses two subwoofers, connect the
Subwoofer 2 Output
-
jack on the AVR to
the Line Input of the second subwoofer.
9. If an external multi-channel audio source with
5.1 or 7.1 outputs such as an external digital
processor/decoder, DVD-Audio or SACD player is
used, connect the outputs of that device to the
8-Channel Direct Inputs
.
Analog Video Equipment
Connections
Analog video equipment is connected in the same
manner as audio components. Again, the use of
high-quality interconnect cables is recommended
to preserve signal quality.
1. Connect a VCR’s audio and video Play/Out
jacks to the
Video 1
or
Video 2 In
jacks
!
%
on the rear panel. The Audio and Video
Record/In jacks on the VCR should be connected
to the
Video 1 Out
jacks
&
on the AVR.
Installation and Connections
29510_AVR745_Engelsk 30/10/06 9:31 Side 14
