Harman Kardon AVR 435, Руководство пользователя

Страница: 52 / 60

will remain illuminated in red. Press the
⁄
/
¤
Navigation Button
o
until
USER RESET
appears on the bottom line of the LCD screen, as
shown in Figure 82.
Figure 82
3. Press the Set Button
q
to reset the remote.
Note that once the Set Button is pressed the
process may not be stopped. While the remote’s
memory is being cleared, a
RESETTING...
message will appear in the upper line of the
remote’s LCD screen as shown in Figure 83.
It may take a few minutes for the reset process
to take place, and the length of time will vary
depending on how much customization and pro-
gramming has taken place. Please be patient; as
long as the message appears in the display the
remote is functioning properly.
Figure 83
4. When the remote has been totally reset and
returned to the factory default condition, a
REMOTE RESET COMPLETE message will
appear (Figure 84) briefly, and then the remote
will return to normal operation.
Figure 84
Device Priority Timing
The remote’s Device Priority mode allows you to
select the length of time that the remote continues to
issue codes for a device other than the AVR once you
use the remote to control a source or other product.
The default operation for the remote is to have all
buttons on the remote return to their AVR functions
5 seconds after the last button press. However, you
may program the AVR remote to remain active as the
source device remote for 12 seconds, or to keep the
source device’s codes active until another
Input
Selector
d
is pressed. If you wish to keep the
default setting of a 5-second return, no changes
are needed.
To change the device priority timing, follow
these steps:
1. Press and hold the Program Button
y
for
about 3 seconds while the message shown in
Figure 24 appears in the remote’s
LCD
Information Display
c
. Release the button
when the red light under the Set Button
q
appears.
2. The remote’s
MAIN MENU
message (Fig. 25)
will appear in the LCD display and the Set Button
q
will remain illuminated in red. Press the ⁄
/
¤
Navigation Buttons
o
until
DEVICE
PRIORITY
appears in the bottom line of the
LCD screen, as shown in Figure 86, and press the
Set Button
q
.
Figure 86
3. When the
DEVICE PRIORITY
message
appears in the remote’s LCD display (Figure 87),
press the
⁄ / ¤
Navigation Buttons
o
to
select the option that best suits your needs.
Figure 87
• When
NORMAL
appears on the bottom line of
the LCD, the AVR remote will revert to AVR control
5 seconds after the last button press, when you
are controlling a source device.
• When
EXTENDED
appears on the bottom
line of the LCD, the AVR remote will revert to AVR
control 12 seconds after the last button press, when
you are controlling a source device.
• When LAST USED appears on the bottom
line of the LCD, once you press one of the Input
Selectors
d
, the AVR remote will continue to
operate as with the codes for the selected source
device, until another device is selected. If you
choose this option, please remember that you will
have to press the
AVR Selector
e
in order to
use the remote to operate the AVR for functions
such as surround mode selection, but the Volume
and Mute controls will continue to remain active in
their AVR modes at all times.
4. Press the Set Button
q
one more time. The
LCD display will show the word
SAVING
on the
top line for about 2 seconds and then flash
SAVED four times on the bottom line to indicate
that the setting has been accepted by the remote’s
memory.
Backlight Options
The AVR 435’s remote has a built-in backlight system
that makes it easier to use the remote when the room
lighting is dimmed for an optimal home theater experi-
ence. To turn the backlighting on, simply press the
Light Button
z
. That button is made from a spe-
cial “glow” material that makes it easier to find in dark
rooms. This glow feature does not use any battery
power, so the glow will fade when the remote is kept
in a dark room for an extended period of time. You
may “recharge” it by placing the remote in normal
room lighting for a few hours.
Once the Light Button
y
is pressed, the remote’s
backlighting will remain on for approximately 7 sec-
onds, and when you press any button on the remote
while the backlighting is on, the light will stay on for
another 7 seconds. However, the remote’s “Couch”
function will conserve battery power by turning both
the backlighting and the LCD display off when any
button is pressed for more than 30 seconds.
You may also configure the remote so that the back-
lighting will come on, any time a button is pressed.
To set this option, follow these steps:
1. Press and hold the Program Button
y
for
about 3 seconds while the message shown in
Figure 24 appears in the remote’s LCD display.
Release the button when the red light under the
Set Button
q
appears.
2. When the remote’s Main Menu message (Fig. 25)
appears in the LCD display and the Set Button
q
remains illuminated in red, press the
⁄ / ¤
Navigation Button
o
until
BACK LIGHT
appears in the bottom line of the LCD screen, as
shown in Figure 88.
Figure 88
3. Press the Set Button
q
and then press the
⁄ / ¤
Navigation Buttons
o
again so that
ON FULL
appears in the bottom line of the
LCD display, as shown in Figure 89.
Figure 89
4. Press the Set Button
q
one more time. The
LCD display will show the word SAVING on the
top line for about 2 seconds and then flash
SAVED
four times on the bottom line to indicate
that the setting has been accepted by the remote’s
memory.
5. The remote’s backlighting will now turn on whenever
a button is pressed. To revert to the original setting,
follow the four steps shown above, but in Step 3,
select the option that has the word
NORMAL
on
the bottom line of the LCD display.
Additional Notes on Configuring and Operating
the Remote
• When the remote is being programmed, it will auto-
matically time-out if no button is pressed within a
B A C K L I G H T
O N F U L L
M A I N M E N U
B A C K L I G H T
D E V I C E P R I O R I T Y
N O R M A L
M A I N M E N U
D E V I C E P R I O R I T Y
R E M O T E R E S E T
C O M P L E T E
R E S E T T I N G . . .
M A I N M E N U
U S E R R E S E T
52 CONFIGURING THE REMOTE
CONFIGURING THE REMOTE
AVR 435 OM 12/27/04 2:58 PM Page 52