background image

22

D.

 OPERATION

WARNINGS

  The BBQ should never be used indoors.
  Read the instructions carefully before using the appliance.
  Caution: Accessible parts may be very hot. Keep young children away.
  This appliance is not intended to be installed or used on a recreational vehicle or marine 

environment.

  This appliance must only be serviced by an authorised person.
  ONLY USE IN WELL VENTILATED AREAS.
  THE BBQ MUST NOT BE INSTALLED UNDER OR ON ANY COMBUSTIBLE MATERIAL. 

MINIMUM CLEARANCE FROM ANY COMBUSTIBLE MATERIALS OF ALL SIDES OF THE 
BBQ IS 600MM AND 1000MM OVERHEAD.

  THIS GAS APPLIANCE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE 

INSTALLATION REQUIREMENTS SUCH AS THE STANDARD FOR GAS INSTALLATIONS 
(AS 5601). ADDITIONALLY, ALL REQUIREMENTS OF THE LOCAL AUTHORITY — LOCAL 
GAS FITTING REGULATIONS, MUNICIPAL BUILDING CODES, ELECTRICAL WIRING 
REGULATIONS, AND ANY OTHER RELEVANT STATUTORY REGULATIONS MUST ALSO BE 
ADHERED TO.

CARBON MONOXIDE HAZARD-THIS APPLIANCE CAN PRODUCE 
CARBON MONOXIDE WHICH HAS NO ODOUR. USING IT IN 
ENCLOSED SPACE (FOR EXAMPLE CARAVAN,TENT, CAR, MOBILE 
HOME) MAY CAUSE DEATH.

SAFETY TIPS

Please observe the following points before using the BBQ:
  Ensure BBQ is placed on horizontal surface.
  DO NOT move appliance whilst in operation.
  Never leave BBQ unattended when hot or in use.
  DO NOT modify this appliance.
  Turn off the gas supply at the gas cylinder after use.
  Do not tamper with any parts. Any modification of this appliance is dangerous and will nullify 

any warranty.

  The use of protective gloves is recommended when cooking or handling any parts of the BBQ 

while it is hot or in use.

  In the event of a gas leak, shut off gas supply immediately and extinguish any flames. 

Contact the Customer Service Helpline.

Содержание HK3797


































Отзывы: