Hardi HC5500 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 80

background image

19

4 - System setup

Tractor installation

Control units

Find a suitable place in the tractor’s cabin to secure the control units
from movement. Best recommended placement is to the right of the
driver seat. The supplied bracket will fit most tractors. Threaded
mounting holes may be hidden behind front corner cover.

Installation of control unit brackets

The supplied tractor pillar bracket (A) has a hole spacing of 100 and 120
mm. Check tractor instructions manual for information regarding
attachment points.

Three tubes (B) are supplied. One, two or all 3 may be used. They can be
bent and shortened. A spacer (C) is also supplied to allow further
attachment possibilities. Find the best solution for your tractor or
vehicle.

Tube (B) plate is staggered so if correctly orientated, all boxes will line up.

The recommended setup is to place the spacer (C) between the two
tubes (B) used for the controllers and the 3rd tube (B) which is to be
mounted in the bracket (A), as shown on the picture.

μ

ATTENTION! An extension cable is available as an option if the HC
5500 control unit is to be placed further away from the EFC
control unit. (Ref. no. 261933)

100 -120mm

A

B

C

«
...
17
18
19
20
21
...
»

Содержание HC5500

















































































Отзывы:

Нет отзывов

Похожие инструкции для HC5500

Бренд: XBOX Страницы: 4

Бренд: Bartlett Страницы: 5

Бренд: Cansec Страницы: 45

Бренд: Cansec Страницы: 43

Бренд: Cansec Страницы: 32

Бренд: Harmonic Drive Страницы: 85

Бренд: Watts Страницы: 12

Бренд: Lancom Страницы: 8

GRAVIMETRIC AUGER FEEDER MGF-ST

Бренд: Maguire Products Страницы: 47

Бренд: Magtrol Страницы: 160

Бренд: Taco Electronic Solutions Страницы: 28

Бренд: YOKOGAWA Страницы: 150

Бренд: YOODA Страницы: 3

Бренд: YMGI Страницы: 8

Бренд: Trane Страницы: 72

Бренд: Decagon Страницы: 27

Бренд: Frico Страницы: 12

Ambience Control 1

Бренд: EuroLite Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды