Hardi HC5500 Скачать руководство пользователя страница 37

Страница: 37 / 80

7 - Menu 3 Calibration

Menu 3.1 Speed calibration

Menu 3.1.1 Sprayer

The calibration process is the same for each sensor type. In the following
example a “speed sensor on sprayer“ is used.

Shortcut

Press

until menu [3.1.1 Sprayer] is shown.

It is possible to connect the speed sensor at different locations. See
chapter 4 - System setup for more about this. They are calibrated in
the following menus:

[3.1.1 Sprayer]Speed sensor on sprayer

[3.1.2 Tractor]Speed sensor on tractor

[3.1.3 Radar]Radar speed sensor

Choose with the navigation keys.

Press

to confirm. The last confirmed sensor is the active speed sensor.

Shortcut

Press

until menu [3.1.X “Speed abc”] is shown.

Choose speed transducer. (Sprayer, Tractor or Radar) [3.1.1 Sprayer]

Press

confirm.

Press

to read PPU value.

ATTENTION! Be aware that even tractor speed sensor and radar speed sensor uses the same connector, then PPU
value may be very different.

The speed transducer can be calibrated theoretically or practically. The
practical method is recommended.

SPEED CALIBRATION

Sprayer

3.1.1

SPRAYER

Constant

3.1.1.1

Содержание HC5500

















































































Результаты поиска

Содержание HC5500

Отзывы:

Похожие инструкции для HC5500

Бренды по названию

Популярные бренды

Hardi HC5500, Инструкция

Результаты поиска

Содержание HC5500

Отзывы:

Похожие инструкции для HC5500

Бренды по названию

Популярные бренды