Hardi HC5500 Скачать руководство пользователя страница 17

Страница: 17 / 80

3 - Description

General keystrokes, Example: Tank contents

The following is a general description in keystrokes and display readout. The following example, of changing the Tank
contents value, is used to illustrate this. Try it! The same method is used in all the menus.

ATTENTION! When a menu is open, the blinking number or value is the one that can be altered.

Press

to enter the menu system [1 MAIN MENU].

The 2nd line will show the menu number.

The 3rd line will read the present menu.

The 4th line will show a choice.

Note the menu number [1] is blinking.

Press

to enter menu [1.1 Daily settings].

Press

to scroll to [1.2 Tank contents].

NOTE! The last digit of the menu number [1.2] is blinking.

Press

to enter [1.2 TANK CONTENTS].

NOTE! The value that can be changed is blinking.

Press

to move the cursor.

Press

to set the desired value.

Press

confirm.

Press

and hold, to exit the menu system.

MAIN MENU

Daily settings

1.2

DAILY SETTINGS

Tank contents

1.2

TANK CONTENTS

XXXX L

Содержание HC5500

















































































Результаты поиска

Содержание HC5500

Отзывы:

Похожие инструкции для HC5500

Бренды по названию

Популярные бренды

Hardi HC5500, Инструкция

Результаты поиска

Содержание HC5500

Отзывы:

Похожие инструкции для HC5500

Бренды по названию

Популярные бренды