background image

Consult Accompanying Documents

Alternating Current, Single Phase

Type B Applied Part

Warning Dangerous: Voltage

Protective Earth (Ground)

Atmospheric Pressure Limits

Humidity Limits

Temperature Transportation Conditions

Weight Limits

a)

Class 1 equipment

b)

Type B equipment

c)

IPX4 ingress of water (ordinary equipment)

d)

e)

Mode of operations continuous with intermittent loading

The following designations of symbols which are found on various labels on the bed and discussed 

in the Manual.

Technical parameters of these beds place them in the following categories:

To avoid overheating the motor after raising and lowering the bed 

three full times in successions, HARD Manufacturing Company 

requires a fifteen minute break before repeating the same 

Equipment not suitable for use in the presence of fammable anaesthetic 
mixture with air or oxygen or nitrous oxide

The nations #1 manufacturer of hospital cribs

CAUTION SHEET

All bolts and other fasteners must be securely tightened and maintained when crib is 
put into service.

Before each usage or assembly, inspect crib for damaged hardware, loose joints, 
missing parts or sharp edges.

Symbology Definitions / Technical Labels

Attention, Consult Accompanying 
Documents

Содержание H1943-CGP













Отзывы: