-7-
HX communication - instructions about the D register address
D-register
address
Parameter
name
Parameter meaning
Parameter setting
Parameter
division
0001
NPV
Current present value (PV)
Read only
*1
Process
0002
NSV
Current set value (SV)
Read only
*1
Process
0004
SSV
Current set value (SV)
Read only
*1
Process
0005
MVOUT
OUT1 control output value of standard type, Total
control output value of heating/cooling type.
Read only
*2
Process
0006
CH1OUT
OUT1 control output value of standard type,
OUT1 control output value of heating/
cooling type.
Read only
*2
Process
0007
CH2OUT
OUT2 control output value of heating/
cooling type.
Read only
*2
Process
0008
PIDNO
When ZONE is OFF, currentlly
applied set value (SV) and PID group
number
0001: SV1, PID group 1
0002: SV2, PID group 2
0003: SV3, PID group 3
When ZONE is OFF, currentlly
applied PID group number
0001: PID group 1
0002: PID group 2
0003: PID group 3
Read only
Process
0009
ALMSTS
Current state of Alarm 1 and Alarm 2:
0000: Alarm 1 OFF, Alarm 2 OFF
0001: Alarm 1 ON, Alarm 2 OFF
0002: Alarm 1 OFF, Alarm 2 ON
0003: Alarm 1 ON, Alarm 2 ON
Read only
Process
0013
OUT2_IND
When the OUT2 control output is SCR
(4-20mA) in Heating / Cooling type,
it shows the temperature controller
"OUT2 indicator" status.
Read only
Process
0014
H1CM
Current measurement value of the
heater break alarm output
Read only
Process
0016
ADESTS
Current situation of the AD error.
0001: AD conversion error
Read only
Process
0017
ERRSTS
Current situation of the input error.
0001:Input sensor Burn-out
0002: RJC error
0004: Input range exceeded
0008: Less than input range
Read only
Process
0018
AT_STS
Autotuning (AT) current state
0000: AT type
9999: AT in progress ("AT indicator" in
the temperature controller front display
blinking)
Read only
Process
0102
ZONE
Zone function set (For the zone position
setting, set in RP parameter of each PID group
0: OFF, 1: ON
Control Group
0104
ARW
ARW (Anti-reset windup) setting
0: AUTO, 50.0 ~ 200.0 %
*2 Control Group
0106
DI.SL
External contact input (DI) function
0: OFF, 1: ON
Control Group
0107
ALPHA Alpha factor of 2 DOF PID
0 ~ 100 %
Control Group
0108
UP.RT
Ramp-up temperature setting
0: OFF / EUS(0~100 %) *1
Control Group
0109
DN.RT
Ramp-down temperature setting
0: OFF / EUS(0~100 %) *1
Control Group
0110
RTMU
Ramp-time unit setting
0: Hour, 1: Min
Control Group
0111
UPTM
Ramp-up time setting
0.01 ~ 99.59 [hh.mm]
*2 Control Group
0112
DNTM
Ramp-down time setting
0.01 ~ 99.59 [hh.mm]
*2 Control Group
0113
RAMPT Ramp type selection
0: A Type, 1: B Type
Control Group
0120
MVMOD
Manual output function (when selecting
the manual output, the "AT indicator" in the
temperature controller front display is steady)
0: AUTO ,
1: MANUAL
Control Group
0121
MANMV Manual output value (Manual MV) set 0 ~ 100 %
Control Group
0122
CTRM
Control mode selection
0: Traditional,
1:2 2 DOF PID (2DOF)
Control Group
0124
HKSL
Hot-key selection
0: Auto-tuning (AT) function
1: Manual output function
Control Group
0300
SVNO
Set value (SV) number selection
1 ~ 3
Set value setting group
0301
SV1
Set value 1 (SV) setting
EU(0 ~ 100 %)
*1
Set value setting group
0302
SV2
Set value 2 (SV) setting
EU(0 ~ 100 %)
*1
Set value setting group
0303
SV3
Set value 3 (SV) setting
EU(0 ~ 100 %)
*1
Set value setting group
0305
AT MODE Auto-tuning (AT) type selection
0: Standard Automatic Operation
1: Low value (PV) type
automatic operation
Auto-tuning Group
0306
AT
Auto-tuning (AT)
0: OFF, 1 ~ 4
Auto-tuning Group
0310
1.P
PID group 1 proportional band
0.0 ~ 999.9 %
*2
PID Group
0311
1.I
PID group 1 integral time
0 ~ 6000 sec
PID Group
0312
1.D
PID group 1 derivative time
0 ~ 6000 sec
PID Group
0313
1.MR
PID group 1 manual reset
-5.0 ~ 105.0 %
*2
PID Group
0314
1.PC
PID group 1 cooling proportional band 0.0 ~ 999.9 %
*2
PID Group
0315
1.IC
PID group 1 cooling integral time
0 ~ 6000 sec
PID Group
0316
1.DC
PID group 1 cooling derivative time
0 ~ 6000 sec
PID Group
0317
1.DB
PID group 1 Heating / Cooling dead band -100.0 ~ 50.0 %
*2
PID Group
0318
1.RP
PID group 1 zone position setting
EU(0 ~ 100 %), (1.RP < 2.RP) *1
PID Group
0320
2.P
PID group 2 proportional band
0.0 ~ 999.9 %
*2
PID Group
0321
2.I
PID group 2 integral time
0 ~ 6000 sec
PID Group
0322
2.D
PID group 2 derivative time
0 ~ 6000 sec
PID Group
0323
2.MR
PID group 2 manual reset
-5.0 ~ 105.0 %
*2
PID Group
0324
2.PC
PID group 2 cooling proportional band 0.0 ~ 999.9 %
*2
PID Group
0325
2.IC
PID group 2 cooling integral time
0 ~ 6000 sec
PID Group
0326
2.DC
PID group 2 cooling derivative time
0 ~ 6000 sec
PID Group
0327
2.DB
PID group 2 Heating / Cooling dead band -100.0 ~ 50.0 %
*2
PID Group
0328
2.RP
PID group 2 zone position setting
EU(0 ~ 100 %), (1.RP < 2.RP) *1
PID Group
0330
3.P
PID group 3 proportional band
0.0 ~ 999.9 %
*2
PID Group
0331
3.I
PID group 3 integral time
0 ~ 6000 sec
PID Group
0332
3.D
PID group 3 derivative time
0 ~ 6000 sec
PID Group
0333
3.MR
PID group 3 manual reset
-5.0 ~ 105.0 %
*2
PID Group
D-register
address
Parameter
name
Parameter meaning
Parameter setting
Parameter
division
0334
3.PC
PID group 3 cooling proportional band 0.0 ~ 999.9 %
*2
PID Group
0335
3.IC
PID group 3 cooling integral time
0 ~ 6000 sec
PID Group
0336
3.DC
PID group 3 cooling derivative time
0 ~ 6000 sec
PID Group
0337
3.DB
PID group 3 Heating / Cooling dead
band
-100.0 ~ 50.0 %
*2
PID Group
0400
HBA
Heater break alarm (HBA) current set 0: OFF, 1 ~ 50 A
Heater break
alarm group
0401
HDB
Heater break alarm (HBA) Hysteresis
(deadband) set.
0 ~ 50
Heater break
alarm group
0410
A1TY
Alarm 1 type setting
0: OFF, 1 ~ 21
Alarm Group
0411
A2TY
Alarm 2 type setting
0: OFF, 1 ~ 21
Alarm Group
0413
A1DB
Hysteresis (dead band) of alarm 1
EUS(0 ~ 100 %)
Alarm Group
0414
A2DB
Hysteresis (dead band) of alarm 2
EUS(0 ~ 100 %)
Alarm Group
0416
AL-1
Set value of alarm 1
PV alarm: EU (-100 ~ 100 %)
Deviation alarm: EUS (-100 ~ 100 %)
*1 Alarm Group
0417
AL-2
Set value of alarm 2
Alarm Group
0500
RET
Retransmission output type selection
0: Indicated value
1: Set value (SV)
2: Control output value (MV)
3: Power SPS for the sensor
Retransmission
group
0501
RET.H
Retransmission output upper limit setting -1999 ~ 9999
Retransmission
group
0502
RET.L
Retransmission output lower limit setting -1999 ~ 9999
Retransmission
group
0503
RET.T
Retransmission output form
0: 4 - 20 mA, 1: 0 - 20 mA
Retransmission
group
0600
OUT
Output type selection
0~12 (refer to the number of
control output type selection)
Output group
0601
o.ACT
Output operation selection
0: Reverse operation (heating),
1: Direct action (cooling)
Output group
0602
CT
Cycle type (Control cycle)
1 ~ 1000 sec
Output group
0603
CTC
Cooling cycle type (cooling control cycle) 1 ~ 1000 sec
Output group
0604
HYS
General type. ON/OFF control hysteresis Standard type,EUS(0~100%) *1
Output group
Heating / Cooling type.
ON/OFF control hysteresis
Heating / Cooling type
0 ~ 10.0%
*2
0605
PO
Output1 setting when input breaks
-5.0~105.0%
*2 Output group
0606
POC
Output2 setting when input breaks
0~105.0%
*2 Output group
0607
OL-H
Output upper limit function
Standard type,
OL-L +1 digit ~ 105.0 %
Heating / Cooling type,
0.0 ~ 105.0 %
*2
Output group
0608
OL-L
Output lower limit function
Standard type,
-0.5 % ~ OL-H-1 digit
Heating / Cooling type,
0.0 ~ 105.0 %
*2
Output group
0610
INP
Input type selection
1~31
Input group
0611
UNIT
Temperature unit selection
0: ℃, 1: ℉
Input group
0612
FR-H
Upper range selection
EU(0 ~ 100 %)
*1 Input group
0613
FR-L
Lower range selection
EU(0 ~ 100 %)
*1 Input group
0614
DP-P
Decimal point position selection
during the voltage input)
0: No decimal points
1: 1 decimal place
2: 2 decimal places
3: 3 decimal places
Input group
0615
SL-H
Scale upper limit setting
(during voltage input)
-1999 ~ 9999
Input group
0616
SL-L
Scale lower limit setting
(during voltage input)
-1999 ~ 9999
Input group
0617
FILT
Measurement value filter selection
0: OFF, 1 ~ 120 sec
Input group
0618
BIAS
Measurement value correction setting EUS(-100 ~ 100%)
*1 Input group
0619
B.OUT
Operation selection when input breaks 0: OFF, 1: UP, 2: DOWN
Input group
0624
HYST
Hysteresis type
0: CENTER ,
1: EDGE
Output group
*1: Please check the presence or absence of the decimal points according to the
input type and range settings
· Set value with decimal points : if you want to input an SV1 of 100.0℃ through
communication, transmit 03E8(100). (03E8 is the hex value of 1000)
· Set value without decimal points: if you want to input an SV1 of 100℃ through
communication, transmit 0064(100). (0064 is the hex value 100)
*2 : Set value with decimal places.
※ For the instructions of the protocol regarding communication, please refer to the
Hanyoung protocol instruction manual on Hanyoung Nux homepage(www.hynux.com).
How to dismantle case
● HX4
● HX3
● HX2
● HX7
● HX9