Hangar 9 Saratoga 40 Скачать руководство пользователя страница 6

Страница: 6 / 40

Hangar 9 Saratoga Assembly Manual



Step 5

Use a file to make flat areas on the bottom of the axle. This

is necessary so the setscrews from the wheel collars have

a surface to bite onto. This will help keep the wheel collars

from vibrating loose in flight.



Step 6

Place a drop of threadlock on a 3mm x 5mm machine screw.

Thread the screw into one of the 11/64-inch wheel collars.

Slide the wheel collar onto the axle as shown. Do not tighten

the screw at this time.



Step 7

Open the bag containing the main 2

-inch (70mm) wheels.

Slide one of the wheels onto the axle. Prepare a second

wheel collar as described in Step 6 and slide it onto the axle.

Position the wheel collar flush with the end of the axle and

use a #2 Phillips screwdriver to tighten the screw, securing

the wheel collar to the axle. The screw will be tightened

down onto the flat made in Step 5.



Step 8

First, slide the wheel against the outer wheel collar. Next

slide the wheel collar next to the landing gear so it is almost

touching the wheel. Use a #1 Phillips screwdriver to tighten

the screw and secure the wheel collar to the axle. The

position of the wheel will be fine-tuned later in this section of

the manual.



Step 9

Slide one of the wheel pants over the wheel and into position

on the landing gear. Note there is a right and left wheel pant

during the installation. Slide a #4 washer onto a 4-40 x 3/8-

inch socket head machine screw. Place a drop of threadlock

on the screw then use a 3/32-inch hex wrench to tighten the

screw, securing the wheel pant to the landing gear.

Содержание Saratoga 40









































Результаты поиска

Содержание Saratoga 40

Отзывы:

Похожие инструкции для Saratoga 40

Бренды по названию

Популярные бренды

Hangar 9 Saratoga 40, Инструкция по сборке

Результаты поиска

Содержание Saratoga 40

Отзывы:

Похожие инструкции для Saratoga 40

Бренды по названию

Популярные бренды