Hangar 9 Saratoga 40 Скачать руководство пользователя страница 32

Страница: 32 / 40

Hangar 9 Saratoga Assembly Manual



Step 7

Place the canopy hatch on the wing by pulling the front

catch rearward and sitting it straight down on the wing.

The front catch will fit into a hole in the fuselage at the

front of the wing.



Step 8

Use a flat screwdriver and the two 1/4-20 x 1-inch nylon

wing bolts to secure the wing and rear of the hatch.

optional Float Installation

Required Parts

Fuselage assembly

Float mount adapter

Landing gear strap (4)
Assembled floats (HAN4015)
#4 x 1/2-inch sheet metal screw (8)
6-inch (152mm) servo extension or Y-harness

Tools and Adhesives

Zap-A-Dap-A-Goo

Threadlock

Phillips screwdriver: #2

Thin CA

Hobby knife with #11 blade

Before starting the installation of your floats, you will

need to assemble them according to the float manual.



Step 1

Locate the float mount adapter, four landing gear straps and

eight #4 x 1/2-inch sheet metal screws.



Step 2

Remove the landing gear from the fuselage. Use the

hardware from the landing gear to attach the float mount

adapter. Make sure to use threadlock on the screws to

prevent them from vibrating loose.



Step 3

Use a hobby knife with a #11 blade to remove the covering

on the bottom of the fuselage where the rear mount of

the float will fit. Holes have also been pre-drilled for the

mounting screws. Use Zap-A-Dap-A-Goo or thin CA to seal

the wood and protect it from water.

Содержание Saratoga 40









































Результаты поиска

Содержание Saratoga 40

Отзывы:

Похожие инструкции для Saratoga 40

Бренды по названию

Популярные бренды

Hangar 9 Saratoga 40, Инструкция по сборке

Результаты поиска

Содержание Saratoga 40

Отзывы:

Похожие инструкции для Saratoga 40

Бренды по названию

Популярные бренды