Hangar 9 Alpha 40 Скачать руководство пользователя страница 31

Страница: 31 / 48

Required Parts

• Transmitter

• Assembled airframe

Required Tools and Adhesives

• Ruler

The control throws from the factory are

preset in the transmitter. This section

has been provided in case any servos or

control surfaces are replaced so the control

throws can be checked at a later date.

Rudder Throw

Use a ruler to check the amount of throw for the rudder.

Move the rudder stick fully and check the measurements.

Adjust the radio as necessary following the instructions

provided with the radio to achieve the following

measurement. The throw will measure:
Low Rate:

1/2-inch (13mm) (11 degrees)

High Rate:

7/8-inch (22mm) (20 degrees)

The throw is measured in both the right and left directions

as shown below.

Low Rate: 1/2-inch (13mm) (11 degrees)

High Rate: 7/8-inch (22mm) (20 degrees)

Note

: The rudder throw is measured

at the bottom of the rudder.

Aileron Throw

Use a ruler to check the amount of throw for the aileron.

Move the aileron stick fully and check the measurements.

Adjust the radio as necessary following the instructions

provided with the radio to achieve the following

measurement. The throw will measure:
Low Rate:

1/4-inch (6mm) (8 degrees)

High Rate:

3/8-inch (10mm) (14 degrees)

The throw is measured in both the up and down directions

as shown below.

Low Rate: 1/4-inch (6mm) (8 degrees)

High Rate: 3/8-inch (10mm) (14 degrees)

elevator Throw

Use a ruler to check the amount of throw for the elevator.

Move the elevator stick fully and check the measurements.

Adjust the radio as necessary following the instructions

provided with the radio to achieve the following

measurement. The throw will measure:
Low Rate:

5/16-inch (8mm) (10 degrees)

High Rate:

1/2-inch (13mm) (16 degrees)

The throw is measured in both the up and down directions

as shown below.

Low Rate: 5/16-inch (8mm) (10 degrees)

High Rate: 1/2-inch (13mm) (16 degrees)

Section 16: Setting the Control Throws

12843.1_HAN_Alpha40_SpektrumManual.indd 31

6/4/10 10:18:40 AM

Содержание Alpha 40

















































Результаты поиска

Содержание Alpha 40

Отзывы:

Похожие инструкции для Alpha 40

Бренды по названию

Популярные бренды

Hangar 9 Alpha 40, Инструкция по сборке

Результаты поиска

Содержание Alpha 40

Отзывы:

Похожие инструкции для Alpha 40

Бренды по названию

Популярные бренды