Hangar 9 Alpha 40 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 48

background image

13



Step 5

Thread the propeller nut onto the engine crankshaft.



Step 6

Use an adjustable wrench to tighten the propeller nut,

securing the propeller and spinner backplate onto the

engine crankshaft.

Important

: When tightening the propeller

nut, always use an adjustable wrench, box

end wrench or 3/8-inch drive socket. Using

pliers will not allow you to place enough

grip to properly tighten the propeller nut.

Note

: Make sure the propeller has not

moved from its position as described back

in Step 3. If it has, the spinner cone will not

be able to be installed in the following steps.



Step 7

Slide the spinner cone over the propeller. It will fit into the

grooves in the spinner backplate when installed.



Step 8

Use the three 3mm x 10mm sheet metal screws supplied

with the spinner to secure the spinner cone to the spinner

backplate. A #1 Phillips screwdriver will be required to

tighten the screws.

Section 3: Propeller and Spinner Installation

12843.1_HAN_Alpha40_SpektrumManual.indd 13

6/4/10 10:18:05 AM

«
...
11
12
13
14
15
...
»

Содержание Alpha 40

















































Отзывы:

Нет отзывов

Похожие инструкции для Alpha 40

Бренд: Jamara Страницы: 28

Бренд: Tumama Kids Страницы: 24

FG-1 Corsair Lucky Gallon

Бренд: H-KING Страницы: 18

Lights & Sounds

Бренд: Learning Resources Страницы: 2

BUILD & REBUILD 10660

Бренд: LEGO Страницы: 24

Three Rivers Fast Freight

Бренд: Lionel Страницы: 24

Big Bird Ride-On

Бренд: Playskool Страницы: 2

GIZMOS & GADGETS

Бренд: Littlebits Страницы: 13

COFFEE CUPS ROUNDABOUTS

Бренд: Faller Страницы: 12

Бренд: LEGO Страницы: 59

Boulton Paul Defiant Mk I

Бренд: WarbirdKits Страницы: 17

Jumpin' Jackpot

Бренд: NAMCO Страницы: 12

Бренд: Fisher-Price Страницы: 6

Бренд: Peg-Perego Страницы: 48

Baby GymTasTics Zebra K0317

Бренд: Fisher-Price Страницы: 6

Бренд: Team Durango Страницы: 44

Mercedes-Benz SLK 55 AMG

Бренд: Jamara Страницы: 4

$K'Nex Education INTERMEDIATE MATH & GEOMETRY 79028 Manual preview$

INTERMEDIATE MATH & GEOMETRY 79028

Бренд: K'Nex Education Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды