Hangar 9 Alpha 40 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 48

background image

20

Required Parts

• Wing assembly

• Fuselage assembly

• Rubber band (10)



Step 1

Locate the aileron extension that is inside the fuselage.

Align the colors from the aileron servo lead with the

extension so they match, then plug them together.



Step 2

Start securing the wing to the fuselage by installing two of

the rubber bands.

Hint

: Always start with the cross rubber

bands. This will keep the wing from

twisting on the fuselage when installing

the remaining rubber bands.



Step 3

Install a second set of rubber bands on the wing

as shown.



Step 4

Continue installing a total of six or more of the rubber

bands, alternating the direction of each set until they have

all been installed.

Hint

: Always end the rubber band installation

by installing the cross rubber bands last.

They will help in keeping all the other rubber

bands in position on the wing dowels.

Hint

: After flying, store your rubber bands in

a bag with a small amount of baby powder.

This will soak up the fuel that is on the

rubber bands, making them last longer.

Section 7: Wing Installation

12843.1_HAN_Alpha40_SpektrumManual.indd 20

6/4/10 10:18:18 AM

«
...
18
19
20
21
22
...
»

Содержание Alpha 40

















































Отзывы:

Нет отзывов

Похожие инструкции для Alpha 40

Бренд: Faller Страницы: 4

Бренд: Carrera RC Страницы: 40

Lynx Mk.8 interior

Бренд: Eduard Страницы: 4

Бренд: BLOTZ Страницы: 2

Бренд: Faller Страницы: 4

Бренд: Eduard Страницы: 4

BARBIE 56759-0920

Бренд: Barbie Страницы: 2

Бренд: Tumama Kids Страницы: 30

Бренд: Eduard Страницы: 4

Бренд: Little Tikes Страницы: 2

Бренд: C&C Models Страницы: 23

3-in-1 Learning Zebra Scooter

Бренд: VTech Страницы: 16

Бренд: M.T.H. Страницы: 36

Бренд: LEXIBOOK Страницы: 52

Бренд: pitsco Страницы: 162

Having a Ball Spin 'n Slide Popper 9176 6WS

Бренд: Bright Starts Страницы: 12

Бренд: Eduard Страницы: 4

Бренд: Mini Gadgets Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды