Hamworthy Wessex 100 M100 Скачать руководство пользователя страница 27

Страница: 27 / 40

HAMWORTHY HEATING LTD

WESSEX 100 M

500001080/F

Figure 12.2a Fault Finding Procedures

Initial Start Procedure

Is the fan running ?

Yes

Continued

Ref Fig 12.2b

Yes

Is mains power on ?

Has the ignition

controller reset ?

Has the air pressure

switch proved ?

Is there a glow at the HSI

probe ?

Is the temperature limiter

reset ? (Indicated on the

fascia as Overheat)

Is there a demand from the

thermostat ?

Is remote control link

(C1-C2) secure ?

Is there power at the

ignition controller ?

Is 'Fan On' neon

illuminated on fascia ?

Replace ignition

controller

Check fuse(s) time clock

etc.

Re-set ignition

controller (Lockout

button on fascia).

Check thermostats.

Check air sensing venturi

and pressure switch

connecting tubes.

Check that the probe and

electrode connections are

secure and sound.

Re-set temperature

limiter (Limit Stat)

Check and turn

thermostat to maximum.

Check and close

remote circuit.

Check wiring

Check fan motor and

air pressure switches

Yes

Содержание Wessex 100 M100









































Результаты поиска

Содержание Wessex 100 M100

Отзывы:

Похожие инструкции для Wessex 100 M100

Бренды по названию

Популярные бренды

Hamworthy Wessex 100 M100, Инструкция по установке, наладке и обслуживанию

Результаты поиска

Содержание Wessex 100 M100

Отзывы:

Похожие инструкции для Wessex 100 M100

Бренды по названию

Популярные бренды